Auto Page rs-1000 User Manual

                     

RS1000 OP 1/07 

14

 

 

 

 

 

 

 

Spin up the

   

switch to the page

 1

 and 

then press the “Silent Disarm” button or press the transmitter 

  and 

  buttons at the same time to disarm your security 

system, No chirp sound will be heard, arm and disarm 

confirmation will be through the vehicles parking lights only. 

TAMPER DISARMING: If alarm triggered, upon disarming the system, the siren will chirp 4 times and 
the parking light will flash 3 times. 
PATHWAY ILLUMINATION: This feature turns the parking lights “ON” for 30 seconds upon an unlock 
signal and for 10 seconds upon the lock signal. (Programming required) 
TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver’s door only when 
disarming the security system. Pushing the   button a second time within 3 seconds will unlock the 
other doors. (Additional installation is required) 
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 
60 seconds after disarming with remote transmitter. Automatic rearm will cancel if the ignition is turned 
ON and will pause if any door is opened before the 60 seconds timer has elapsed. 

OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting) 
The Override function may be used if the remote transmitter is lost or inoperative. 

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 
2. Within 10 seconds push and release the valet switch 

The alarm will stop sounding and enter the disarmed mode. You can now start and operate the vehicle 
normally. 

If the valet switch is located in a place that can be easily found, this security system allows the consumer 
to program a password pin code offering a higher level of security. 
1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.) 
2. Within 5 seconds, enter your chosen the first digit code by pressing and releasing the Valet Switch. 

(When you are finished with the above procedures, the system's siren stops alarming and the parking 
lights stop flashing, but the vehicle cannot be started and driven away.) 

3. If you use one digit to be a password pin code, skip to Step 6. If you use two digits to be a password pin 

code, advance to Step 4. 

4. Within 15 seconds of the last digit code enter (the 1st code), turn the Ignition Switch “Off” and then “On”. 
5. Within 15 seconds, enter your chosen of the second digit code by press and release the Valet Switch. 
6. Turn the ignition switch to the “OFF” position. [4] Chirps form siren/horn, [3] flash from parking light to 

indicate the system was disarmed. 

Note: If someone keys-in the wrong password pin code, the system allows him to make 2 mistakes. If the 
            third code is still wrong, it will automatically shut down for 5 minutes. During this period the system   
            will not accept any code and the LED will “pause on” (the LED will turn on 1 second   
      and turn off 0.1 second). 

EXAMPLE: To Override The System With The Password Code 83, you would; 
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)   
2. Within 5 seconds, Press and Release the Valet Switch 8 times 

(When finish the above procedure, the system's siren will stop alarming and the parking lights will stop 
flashing, but the vehicle cannot be started and driven away.) 

3. Within 15 seconds of the last digit code enter (the 1

st

 code), turn the Ignition Switch “Off” and then “ON”. 

4. Within 15 seconds, Press and Release the Valet Switch 3 times 
5. Turn the Ignition Switch to “Off” position. [4] Chirps form siren/horn and    [3] flashes from the parking 

light will indicate the system has been disarmed. 

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your