Alliance Laundry Systems 504523R3 User Manual
504523
31
Additional Dryer Security . . .
(Metered Models)
Enclosed in the shipping bag are four tamper-resistant
screws. When used, these screws will provide additional
security for your dryer.
screws. When used, these screws will provide additional
security for your dryer.
Located on the service door of the dryer is a flat Phillips
head screw. During shipment, this screw is used to attach
the service door to the meter case. For additional
security, this screw can be reinstalled inside the control
hood of your washer.
head screw. During shipment, this screw is used to attach
the service door to the meter case. For additional
security, this screw can be reinstalled inside the control
hood of your washer.
The following list is the procedure required to install the
Phillips head screw and tamper-resistant screws:
Phillips head screw and tamper-resistant screws:
1. Remove the Phillips head screw from service door
(see illustration).
2. Remove two screws holding control panel to control
hood.
3. Tilt control panel forward and lay on a protective pad
to prevent scratching of cabinet top.
4. Insert phillips head screw down through double “D”
hole in left rear corner of cabinet top (inside control
hood) until it engages retainer nut located on left rear
corner gusset of cabinet.
hood) until it engages retainer nut located on left rear
corner gusset of cabinet.
5. Finger tighten screw.
IMPORTANT: Do not use a power driver to tighten
screw. Torque of a power driver could over-tighten
screw causing damage to cabinet assembly.
screw. Torque of a power driver could over-tighten
screw causing damage to cabinet assembly.
6. Secure control panel to control hood using two No. 8
tamper-resistant screws, Part No. 35528.
7. While supporting lower access panel, remove two
screws from bottom edge. Gently lower access panel
to disengage guide lugs from bottom edge of front
panel.
to disengage guide lugs from bottom edge of front
panel.
8. Remove two screws holding bottom tabs on front
panel to dryer cabinet. Swing bottom of front panel
away from dryer far enough to disengage hold-down
clips and guide lugs from cabinet top.
away from dryer far enough to disengage hold-down
clips and guide lugs from cabinet top.
9. Disconnect wires from door switch.
NOTE: Refer to wiring diagram when rewiring
switch.
switch.
10. Remove two cabinet top hold-down scerws and
install two #10 tamper-resistant screws, Part No.
62853.
62853.
11. Reinstall door switch and front panel and install two
#10 tamper-resistant screws, Part No. 62853 to
secure lower access panel.
secure lower access panel.
NOTE: Tamper-resistant bits and bit holder, for
installation of tamper-resistant screws, are available
as optional equipment at extra cost.
installation of tamper-resistant screws, are available
as optional equipment at extra cost.
To reduce the risk of electric shock, fire,
explosion, serious injury or death:
• Disconnect electric power to the dryer
explosion, serious injury or death:
• Disconnect electric power to the dryer
before servicing.
• Never start the dryer with any guards/
panels removed.
• Close gas shut-off valve to gas dryer before
servicing.
• Whenever ground wires are removed
during servicing, these ground wires must
be reconnected to ensure that the dryer is
properly grounded.
be reconnected to ensure that the dryer is
properly grounded.
W138
WARNING
DOUBLE
“D” HOLE
#8 SCREWS
35528
#10 SCREWS
62853
#10 SCREWS
62853
D237IE1A
Bit (No. 8 screws) ................... Part No. 281P4
Bit (No. 10 screws) ................. Part No. 282P4
Bit Holder (3/8 drive).............. Part No. 24161