SMSC LAN91C111 User Manual
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
Revision 1.91 (08-18-08)
86
SMSC LAN91C111 REV C
DATASHEET
10.3
Typical Flow of Events for Transmit (Auto Release = 1)
6
Upon transmit completion the first word in memory is
written with the status word. The packet number is
moved from the TX FIFO into the TX completion
FIFO. Interrupt is generated by the TX completion
FIFO being not empty.
If a TX failure occurs on any packets, TX INT is
generated and TXENA is cleared, transmission
sequence stops. The packet number of the failure
packet is presented at the TX FIFO PORTS Register.
written with the status word. The packet number is
moved from the TX FIFO into the TX completion
FIFO. Interrupt is generated by the TX completion
FIFO being not empty.
If a TX failure occurs on any packets, TX INT is
generated and TXENA is cleared, transmission
sequence stops. The packet number of the failure
packet is presented at the TX FIFO PORTS Register.
7
SERVICE INTERRUPT - Read Interrupt Status
Register. If it is a transmit interrupt, read the TX FIFO
Packet Number from the FIFO Ports Register. Write
the packet number into the Packet Number Register.
The corresponding status word is now readable from
memory. If status word shows successful
transmission, issue RELEASE packet number
command to free up the memory used by this packet.
Remove packet number from completion FIFO by
writing TX INT Acknowledge Register.
Option 1) Release the packet.
Option 2) Check the transmit status in the EPH
STATUS Register, write the packet number of the
current packet to the Packet Number Register, re-
enable TXENA, then go to step 4 to start the TX
sequence again.
Register. If it is a transmit interrupt, read the TX FIFO
Packet Number from the FIFO Ports Register. Write
the packet number into the Packet Number Register.
The corresponding status word is now readable from
memory. If status word shows successful
transmission, issue RELEASE packet number
command to free up the memory used by this packet.
Remove packet number from completion FIFO by
writing TX INT Acknowledge Register.
Option 1) Release the packet.
Option 2) Check the transmit status in the EPH
STATUS Register, write the packet number of the
current packet to the Packet Number Register, re-
enable TXENA, then go to step 4 to start the TX
sequence again.
S/W DRIVER
MAC SIDE
1
ISSUE ALLOCATE MEMORY FOR TX - N BYTES -
the MMU attempts to allocate N bytes of RAM.
the MMU attempts to allocate N bytes of RAM.
2
WAIT FOR SUCCESSFUL COMPLETION CODE -
Poll until the ALLOC INT bit is set or enable its mask
bit and wait for the interrupt. The TX packet number
is now at the Allocation Result Register.
Poll until the ALLOC INT bit is set or enable its mask
bit and wait for the interrupt. The TX packet number
is now at the Allocation Result Register.
3
LOAD TRANSMIT DATA - Copy the TX packet
number into the Packet Number Register. Write the
Pointer Register, then use a block move operation
from the upper layer transmit queue into the Data
Register.
number into the Packet Number Register. Write the
Pointer Register, then use a block move operation
from the upper layer transmit queue into the Data
Register.
4
ISSUE "ENQUEUE PACKET NUMBER TO TX FIFO"
- This command writes the number present in the
Packet Number Register into the TX FIFO. The
transmission is now enqueued. No further CPU
intervention is needed until a transmit interrupt is
generated.
- This command writes the number present in the
Packet Number Register into the TX FIFO. The
transmission is now enqueued. No further CPU
intervention is needed until a transmit interrupt is
generated.
5
The enqueued packet will be transferred to the MAC
block as a function of TXENA (nTCR) bit and of the
deferral process (1/2 duplex mode only) state.
block as a function of TXENA (nTCR) bit and of the
deferral process (1/2 duplex mode only) state.
6
Transmit pages are released by transmit completion.
S/W DRIVER
MAC SIDE