Philips FW-C80 User Manual

21

3139 116 19681

Notes:
– It is not possible to change tape side

during recording.

– For recording, use only tape of IEC type I

(normal tape) or IEC type II (Cr02).

– The tape is secured at both ends with

leader tape. At the beginning and end of
tape, nothing will be recorded for six to
seven seconds.

– The recording level is set automatically,

regardless of the position of Volume,
wOOx, DSC, etc.

– To prevent accidental recording, break

out the tab on the left shoulder of the
tape side you want to protect.

– If  “

CHECK TAPE” is displayed, the

protection tab has been broken.  Put a
piece of clear adhesive tape over the
opening.  Do not cover the Cr02 tape

detection hole when covering the tab
opening.

For CD digital recording, please refer to the
Instructions Manual of the CD Recorder,
digital audio equipment, etc.

(only on tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape

deck 2.

2 Load a blank tape into tape deck 2 with

the open side downward.

3 Press í or ë to select the recording

tape side 

(see Tape Side under TAPE

section).

4 Press CD, TUNER or AUX.
• Start playback of the selected source.
5 Press RECORD to start recording.

™ The 

 starts flashing.

6 Press Ç to stop recording.

Notes:
– Only  

å

å

å

å

å  or  ∂

∂

∂

∂

∂ mode is available

during recording .

– During recording, it is not possible to

listen to another source.

(from tape deck 1 to

tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape

deck 2.

2 Load the prerecorded tape into tape

deck 1 with full spool to the left and a
blank tape into tape deck 2 with full
spool aside.

3 Press í or ë to select the recording

tape side 

(see Tape Side under TAPE

section).

4 Press DUB (HSD) 

once for normal

speed dubbing or 

twice (within 2

seconds) for high speed dubbing.
™ "NORMAL" (normal speed) or

"

FAST" (high speed) will be

displayed, followed by "

DUB" with "!

or

 @" scrolling left or right  depending

on the tape side selected.

™ The 

 appears on the display

during high speed dubbing.

• Dubbing will start immediately.

™ The 

 starts flashing.

5 Press Ç to stop dubbing.

Notes:
– Only 

å 

å 

å 

å 

å mode is available during

dubbing.

– At the end of side A, flip the tapes to

side B and repeat the procedure.

– Dubbing of tapes is only possible from

tape deck 1 to tape deck 2.

– To ensure good dubbing, use tapes of

the same length.

– During high speed dubbing in Tape

mode, the sound is reduced to a low
volume.

– You can listen to another source while

dubbing.

1 Load a blank tape into tape deck 2 and a

disc into a disc tray.

2 Press CD to select CD mode.
• You can program the tracks in the order

you want them to be recorded (see
Programming Tracks). If not,  select the
disc by pressing CD (CD 1•2•3) and the
tracks are recorded according to the
order on the selected disc.

3 Press RECORD to start recording.

™ The 

 starts flashing.

• CD will start playback automatically.
4 Press Ç to stop recording.

• For One Touch Recording, as soon as you

press RECORD, the current source (CD,
TUNER or AUX) will be recorded on tape
deck 2.

1 Load a blank tape in tape deck 2.
2 Press RECORD to start recording.

™ The 

 starts flashing.

3 Press Ç to stop recording.

Note:
– When you press RECORD while in TAPE

mode, "

SELECT SOURCE" will be

displayed.  One Touch Recording is not
possible in TAPE mode.

pg 01-26/C80/22-Eng

3/6/00, 2:24 PM

21