Philips FW-C80 Manuel D’Utilisation
21
English
3139 116 19681
Notes:
– It is not possible to change tape side
– It is not possible to change tape side
during recording.
– For recording, use only tape of IEC type I
(normal tape) or IEC type II (Cr02).
– The tape is secured at both ends with
leader tape. At the beginning and end of
tape, nothing will be recorded for six to
seven seconds.
tape, nothing will be recorded for six to
seven seconds.
– The recording level is set automatically,
regardless of the position of Volume,
wOOx, DSC, etc.
wOOx, DSC, etc.
– To prevent accidental recording, break
out the tab on the left shoulder of the
tape side you want to protect.
tape side you want to protect.
– If “
CHECK TAPE” is displayed, the
protection tab has been broken. Put a
piece of clear adhesive tape over the
opening. Do not cover the Cr02 tape
piece of clear adhesive tape over the
opening. Do not cover the Cr02 tape
detection hole when covering the tab
opening.
opening.
Digital Recording via Digital
Out
Out
For CD digital recording, please refer to the
Instructions Manual of the CD Recorder,
digital audio equipment, etc.
Instructions Manual of the CD Recorder,
digital audio equipment, etc.
RECORDING
Recording from other sources
(only on tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape
1 Press TAPE ( TAPE 1•2 ) to select tape
deck 2.
2 Load a blank tape into tape deck 2 with
the open side downward.
3 Press í or ë to select the recording
tape side
(see Tape Side under TAPE
section).
4 Press CD, TUNER or AUX.
• Start playback of the selected source.
5 Press RECORD to start recording.
• Start playback of the selected source.
5 Press RECORD to start recording.
™ The
REC
starts flashing.
6 Press Ç to stop recording.
Notes:
– Only
– Only
å
å
å
å
å or ∂
∂
∂
∂
∂ mode is available
during recording .
– During recording, it is not possible to
listen to another source.
Dubbing tapes
(from tape deck 1 to
tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape
1 Press TAPE ( TAPE 1•2 ) to select tape
deck 2.
2 Load the prerecorded tape into tape
deck 1 with full spool to the left and a
blank tape into tape deck 2 with full
spool aside.
blank tape into tape deck 2 with full
spool aside.
3 Press í or ë to select the recording
tape side
(see Tape Side under TAPE
section).
4 Press DUB (HSD)
once for normal
speed dubbing or
twice (within 2
seconds) for high speed dubbing.
™ "NORMAL" (normal speed) or
™ "NORMAL" (normal speed) or
"
FAST" (high speed) will be
displayed, followed by "
DUB" with "!
or
@" scrolling left or right depending
on the tape side selected.
™ The
HSD
appears on the display
during high speed dubbing.
• Dubbing will start immediately.
™ The
REC
starts flashing.
5 Press Ç to stop dubbing.
Notes:
– Only
– Only
å
å
å
å
å mode is available during
dubbing.
– At the end of side A, flip the tapes to
side B and repeat the procedure.
– Dubbing of tapes is only possible from
tape deck 1 to tape deck 2.
– To ensure good dubbing, use tapes of
the same length.
– During high speed dubbing in Tape
mode, the sound is reduced to a low
volume.
volume.
– You can listen to another source while
dubbing.
CD Synchro Start Recording
1 Load a blank tape into tape deck 2 and a
disc into a disc tray.
2 Press CD to select CD mode.
• You can program the tracks in the order
• You can program the tracks in the order
you want them to be recorded (see
Programming Tracks). If not, select the
disc by pressing CD (CD 1•2•3) and the
tracks are recorded according to the
order on the selected disc.
Programming Tracks). If not, select the
disc by pressing CD (CD 1•2•3) and the
tracks are recorded according to the
order on the selected disc.
3 Press RECORD to start recording.
™ The
REC
starts flashing.
• CD will start playback automatically.
4 Press Ç to stop recording.
4 Press Ç to stop recording.
One Touch Recording
• For One Touch Recording, as soon as you
press RECORD, the current source (CD,
TUNER or AUX) will be recorded on tape
deck 2.
TUNER or AUX) will be recorded on tape
deck 2.
1 Load a blank tape in tape deck 2.
2 Press RECORD to start recording.
2 Press RECORD to start recording.
™ The
REC
starts flashing.
3 Press Ç to stop recording.
Note:
– When you press RECORD while in TAPE
– When you press RECORD while in TAPE
mode, "
SELECT SOURCE" will be
displayed. One Touch Recording is not
possible in TAPE mode.
possible in TAPE mode.
pg 01-26/C80/22-Eng
3/6/00, 2:24 PM
21