Hitachi cg32w460n User Manual
GB - 14 -
Sound Indicator
This is a stereo option. The alternatives of the indicator are
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. " I-II"
button is used to select Mono or Stereo, or Dual I or Dual II.
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. " I-II"
button is used to select Mono or Stereo, or Dual I or Dual II.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual I is selected in default and also
can be selected after Dual II by Remote Control.
can be selected after Dual II by Remote Control.
If Dual II selected by Remote Control.
Picture Mode
The picture mode OSD is displayed below the sound indicator,
by TV Status OSD’s. According to the WSS data, inside of the
OSD box “4:3”, “16:9”, “14:9”, “CINE”, “SUBT” or “AUTO” is writ-
ten.
By pressing “
by TV Status OSD’s. According to the WSS data, inside of the
OSD box “4:3”, “16:9”, “14:9”, “CINE”, “SUBT” or “AUTO” is writ-
ten.
By pressing “
” button (if Teletext is not active) the picture
mode can be switched into 4:3, 16:9, 14:9, CINEMA, SUBTITLE
or AUTO Mode.
or AUTO Mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it after
3 seconds.
If there is only one minute of the countdown left of the timer, it
is displayed automatically on the upper left of the screen, and
stays there until time is reached. Then TV goes automatically
to stand-by.
activated it is displayed with the TV status and erased with it after
3 seconds.
If there is only one minute of the countdown left of the timer, it
is displayed automatically on the upper left of the screen, and
stays there until time is reached. Then TV goes automatically
to stand-by.
Mute Indicator
It is placed in the upper middle of the screen when enabled, and
it stays there until it is disabled.
it stays there until it is disabled.
To cancel mute, there are two alternative; the first one is press-
ing to " " button, thus volume is set to the preceding value, and
the second one is increasing the volume level, thus it starts at
the minimum level to increase. By decreasing the volume level
in mute state, mute will not be ignored, only the volume level will
decrease. If mute is cancelled after decreasing the volume level,
the volume will return at the decreased level.
ing to " " button, thus volume is set to the preceding value, and
the second one is increasing the volume level, thus it starts at
the minimum level to increase. By decreasing the volume level
in mute state, mute will not be ignored, only the volume level will
decrease. If mute is cancelled after decreasing the volume level,
the volume will return at the decreased level.
No-Signal
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid signal
detected. It shows the time remaining before the switching to the
Stand-By mode (it takes 5 minutes when no signal detected or
no any Remote Control command is accessed). The indicator
is displayed for 3 seconds when there is no valid signal.
After a Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is ini-
tialized to 5 minutes and starts 3 seconds later again to count
down.
detected. It shows the time remaining before the switching to the
Stand-By mode (it takes 5 minutes when no signal detected or
no any Remote Control command is accessed). The indicator
is displayed for 3 seconds when there is no valid signal.
After a Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is ini-
tialized to 5 minutes and starts 3 seconds later again to count
down.
It is not valid in AV mode.
Blue Background During No-Signal
In case, no valid signal is detected (in TV or AV mode) Blue
Background is activated.During search process Blue Back-
ground is not active. But instead there is another feature given;
the semi-transparent menu background is becomes blue.
Background is activated.During search process Blue Back-
ground is not active. But instead there is another feature given;
the semi-transparent menu background is becomes blue.
Volume Bar
It is displayed in the lower middle of the screen. When a volume
command is received (pressing “VOL+” or “VOL-” by Remote
Control or Front panel) and no menu is active, it stays on the
screen for 3 seconds, after the last volume command or until
another command is received in between.
command is received (pressing “VOL+” or “VOL-” by Remote
Control or Front panel) and no menu is active, it stays on the
screen for 3 seconds, after the last volume command or until
another command is received in between.
AV Modes
By pressing the “
” button you can switch your TV to AV
V
modes (except being in Teletext). Pressing this button will
consecutively switch the TV in one of the optional AV modes:
AV-1, AV-2, F-AV (Front AV), RGB (EXT.1) or SVHS (EXT.2).
AV-1 supports the RGB mode and AV-2 supports SVHS mode.
In order to quit the AV mode press the “
consecutively switch the TV in one of the optional AV modes:
AV-1, AV-2, F-AV (Front AV), RGB (EXT.1) or SVHS (EXT.2).
AV-1 supports the RGB mode and AV-2 supports SVHS mode.
In order to quit the AV mode press the “
TV
” button.
Teletext
Teletext is an information system that displays text on your TV
screen. Using the Teletext information system you can view a
page of information on a subject that is available in the list of
contents (index).
On screen display is not available in text mode.
Contrast, brightness or colour control is not available, but vol-
ume control is available in text mode.
screen. Using the Teletext information system you can view a
page of information on a subject that is available in the list of
contents (index).
On screen display is not available in text mode.
Contrast, brightness or colour control is not available, but vol-
ume control is available in text mode.
To operate Teletext
• Select a TV station on which Teletext is being transmitted.
• Press (TELETEXT) “
• Press (TELETEXT) “
” button. Usually the list of contents
(index) is displayed on the screen.
To select a page of Teletext
• Press the appropriate digit buttons for the required Teletext
page number.
The selected page number is displayed at the top left corner of
the screen. The Teletext page counter searches until the se-
lected page number is located, so that the desired page is dis-
played on the screen.
the screen. The Teletext page counter searches until the se-
lected page number is located, so that the desired page is dis-
played on the screen.
• Press “ ” button to move the Teletext screen forward one
page at a time.
• Press “ ” button to move the Teletext screen backward one
page at a time.
01-ENG-(CG32W460AN)-3253W-3040-AK37-ST7P-PLLFS-APS-BG-50050266.p65
13.07.2004, 13:42
14