Campbell Hausfeld HG3000 Series User Manual
General Safety
(continued)
22. Drain tanks of moisture after each
day’s use. If unit will not be used
for a while, it is best to leave drain
cock open until such time as it is to
be used. This will allow moisture
to completely drain out and help
prevent corrosion of inside of tank.
for a while, it is best to leave drain
cock open until such time as it is to
be used. This will allow moisture
to completely drain out and help
prevent corrosion of inside of tank.
23. Inspect tank yearly for rust, pin holes
or any other imperfections that
could cause it to become unsafe.
NEVER weld or drill holes in air tank.
could cause it to become unsafe.
NEVER weld or drill holes in air tank.
24. Household use only.
25. To reduce the risk of electrical shock,
25. To reduce the risk of electrical shock,
do not expose to rain. Store indoors.
Never attempt to
repair or modify
a tank! Welding, drilling or any other
modification will weaken the tank resulting
in damage from rupture or explosion.
Always replace worn or damaged tanks.
modification will weaken the tank resulting
in damage from rupture or explosion.
Always replace worn or damaged tanks.
Drain liquid from
tank daily.
SpraYinG precaUtionS
Do not spray
flammable materials
in vicinity of open flame or near ignition
sources including the compressor unit.
sources including the compressor unit.
1. Spray in a well ventilated area, to
keep fumes from collecting and
causing health and fire hazards.
causing health and fire hazards.
2. Do not spray in vicinity of open
flames or other places where a spark
can cause ignition. Do not smoke
when spraying paint, insecticides, or
other flammable substances.
can cause ignition. Do not smoke
when spraying paint, insecticides, or
other flammable substances.
3. Use a respirator when spraying.
4. Do not direct paint or other sprayed
4. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from
the spraying area as possible to
minimize overspray accumulation on
the compressor.
compressor as far away from
the spraying area as possible to
minimize overspray accumulation on
the compressor.
5. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
the instructions provided by the
chemical manufacturer.
6. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
substances.
7. Use a face mask/
respirator when
spraying and spray in a
well ventilated area to
prevent health and fire hazards.
spraying and spray in a
well ventilated area to
prevent health and fire hazards.
8. Do not direct airstream at body.
assembly
aSSeMblY toolS reqUireD
Tools (not provided) for assembly:
- (1) #2 Phillips screwdriver
- (2) adjustable wrenches
wheel aSSeMblY (FiGUre 1)
Wheel assembly kit includes:
- (2) wheels
- (2) axle bolts
- (2) wheel inserts
- (2) washers
- (2) nuts
1. Wheel has an offset hub. With
Tools (not provided) for assembly:
- (1) #2 Phillips screwdriver
- (2) adjustable wrenches
wheel aSSeMblY (FiGUre 1)
Wheel assembly kit includes:
- (2) wheels
- (2) axle bolts
- (2) wheel inserts
- (2) washers
- (2) nuts
1. Wheel has an offset hub. With
offset hub facing axle iron,
assemble axle bolt through wheel
insert, holes in wheel and axle iron.
assemble axle bolt through wheel
insert, holes in wheel and axle iron.
2. Place adjustable wrench on axle
bolt. Using a second adjustable
wrench, tighten nut securely to
threaded part of axle bolt.
wrench, tighten nut securely to
threaded part of axle bolt.
3. Repeat procedure with other side.
hanDle aSSeMblY (FiGUre 2)
Never use the
handle to lift the
unit completely off the ground. Only
use the handle to lift one end so the
wheels may be used to move the unit.
use the handle to lift one end so the
wheels may be used to move the unit.
Handle assembly kit includes:
- (1) handle
- (4) bolts
1. Insert ends of handle into tube
- (1) handle
- (4) bolts
1. Insert ends of handle into tube
shaped brackets on tank.
2. Align screw holes.
3. Thread screw into hole until tight.
4. Tighten securely with #2 Phillips
3. Thread screw into hole until tight.
4. Tighten securely with #2 Phillips
screwdriver.
3
hG3000 Series, hJ3001 Series, hJ3002 Series
www.chpower.com
Figure 2 - handle assembly
Bolt
Handle
Bolt
Figure 1 - wheel assembly
Wheel
Nut
Bolt
Washer
Wheel insert