APC Symmetra PX 20kW Scalable to 40kW N+1, 400V SY20K40H User Manual
Product codes
SY20K40H
Maintenance Bypass Panel 60kW /
Symmetra
®
PX 10 - 40 kW, 400V
990-1277
Maintenance Bypass Panel 60kW /
Symmetra
®
PX 10 - 40 kW, 400V
990-1277
Maintenance Bypass 60kW /
Symmetra
®
PX 10 - 40 kW, 400V
990-1277
Maintenance Bypass Panel
(MBP) 60 kW
for
Symmetra
®
PX 10 - 40kW, 400 V
1
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This guide contains important instructions for the UPS and MBP that should be followed dur-
ing the handling of UPS, batteries and MBP.
ing the handling of UPS, batteries and MBP.
WARNING!
Risk of Electric Shock.
CAUTION!
Read this important information.
Indicates that a switch or current protection
device is in the “ON” position.
device is in the “ON” position.
Indicates that a switch is in the “OFF” position.
•
All electrical power and power control wiring must be installed by a qualified electrician
and comply with local and national regulations.
•
Before working on the MBP, ensure that mains power is disconnected to the MBP and that
Q1, Q2 and Q3 are in the OFF position.
Q1, Q2 and Q3 are in the OFF position.
Figure 1.1
Figure 1.2
2
Total Power OFF Procedure
Figure 2.1
3
System Electrical Requirements
Do not lift heavy loads
without assistance.
without assistance.
< 18 kg
18 - 32 kg
32 - 54 kg
>54 kg
Install the Maintenance Bypass Panel in an Indoor, Controlled Environment
Temperature
Range:
0°-40°C
Keep Ventilated
Front-to-Rear
Airflow
Relative
Humidity: <95%
Non-condensing
Free of Conductive
Dust or
Corrosive Fumes
Max.
Elevation:
0-3,000 m
0-3,000 m
Full Heat Loss at Nominal Mains: 9,496 BTU/hr (2,780 Watts)
CAUTION!
All electrical power and power control wiring must be installed by a qualified
electrician, and must comply with local and national regulation for maximum power
rating.
electrician, and must comply with local and national regulation for maximum power
rating.
UPS 40kW (40kVA) Output Rating
Input Voltage +/- 15% at nominal voltages
3-Phase
380V 400V 415V
Input Current (nominal, per phase)
66A 62A 60A
Maximum Input Current (continuous, at minimum mains voltage)
88 A
Input Current Protection (external to enclosure, not supplied)
100A *note 4
Input Frequency
50 Hz
1
S
y
m
m
et
ra
®
P
X
1
0
-
4
0
k
W
,
2
0
0
V
B
a
si
c
O
p
er
a
ti
o
n
G
u
id
e
S
y
m
m
et
ra
®
P
X
1
0
-
4
0
k
W
,
2
0
0
V
B
a
si
c
O
p
er
a
ti
o
n
G
u
id
e
?
BATTERY UN
IT
BATTERY UN
IT
BATTERY UNIT
BATTERY UN
IT
Mains Power in the
Off Position
Off Position
2
3
DC Disconnect
Switch in the
Off position.
Switch in the
Off position.
System Enable
Switch in the
Off position.
Switch in the
Off position.
4
All power and
battery
modules must
be removed
battery
modules must
be removed
4