Metra AX-ADXSVI-CH3 Leaflet

INSTAX-ADXSVI-CH3

1-800-221-0932

metraonline.com

REV. 12/19/13

INSTAX-ADXSVI-CH3

1-800-221-0932

metraonline.com

REV. 12/19/13

INSTAX-ADXSVI-CH3

1-800-221-0932

metraonline.com

REV. 12/19/13

INSTAX-ADXSVI-CH3

1-800-221-0932

metraonline.com

REV. 12/19/13

• Connect the

Gray wire to the right front positive speaker output of the

aftermarket radio.

• Connect the

Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the

Green wire to the radio’s left rear positive speaker output.

• Connect the

Green/Black wire to the radio’s left rear negative speaker output.

• Connect the

Purple wire to the radio’s right rear positive speaker output.

• Connect the

Purple/Black wire to the radio’s right rear negative speaker output.

The following wires are for the aftermarket radios that have navigation built in.

• Connect the

Light Green wire to the parking brake wire of the aftermarket

navigation radio (if applicable).

• Connect the

Blue/Pink wire to the VSS or speed sense wire of the aftermarket

navigation radio (if applicable).

• Connect the

Green/Purple wire to the reverse wire of the aftermarket navigation

radio (if applicable).

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to

test the radio.

RCA CONNECtiONS

• Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE

back up camera (if equipped).

• Connect the White and Red RCA to the audio "AUX in" of the aftermarket radio to

retain the OE 3.5mm jack (if equipped).

ASWC-1 (if installing)

After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the

AX-ADXSVI-CH3 and refer to the ASWC-1 instructions.

Caution: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the

aftermarket radio.

NOWLEDGE IS

OWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.

Metra recommends MECP
certified technicians

Caution: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the

aftermarket radio.

NOWLEDGE IS

OWER

Enhance your installation and fabrication skills by

Metra recommends MECP
certified technicians

Caution: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the

aftermarket radio.

NOWLEDGE IS

OWER

Enhance your installation and fabrication skills by

Metra recommends MECP
certified technicians

Caution: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the

aftermarket radio.

NOWLEDGE IS

OWER

Enhance your installation and fabrication skills by

Metra recommends MECP
certified technicians

• Connect the

Gray wire to the right front positive speaker output of the

aftermarket radio.

• Connect the

Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the

Green wire to the radio’s left rear positive speaker output.

• Connect the

Green/Black wire to the radio’s left rear negative speaker output.

• Connect the

Purple wire to the radio’s right rear positive speaker output.

• Connect the

Purple/Black wire to the radio’s right rear negative speaker output.

The following wires are for the aftermarket radios that have navigation built in.

• Connect the

Light Green wire to the parking brake wire of the aftermarket

navigation radio (if applicable).

• Connect the

Blue/Pink wire to the VSS or speed sense wire of the aftermarket

navigation radio (if applicable).

• Connect the

Green/Purple wire to the reverse wire of the aftermarket navigation

radio (if applicable).

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to

test the radio.

RCA CONNECtiONS

• Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE

back up camera (if equipped).

• Connect the White and Red RCA to the audio "AUX in" of the aftermarket radio to

retain the OE 3.5mm jack (if equipped).

ASWC-1 (if installing)

After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the

AX-ADXSVI-CH3 and refer to the ASWC-1 instructions.

• Connect the

Gray wire to the right front positive speaker output of the

aftermarket radio.

• Connect the

Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the

Green wire to the radio’s left rear positive speaker output.

• Connect the

Green/Black wire to the radio’s left rear negative speaker output.

• Connect the

Purple wire to the radio’s right rear positive speaker output.

• Connect the

Purple/Black wire to the radio’s right rear negative speaker output.

The following wires are for the aftermarket radios that have navigation built in.

• Connect the

Light Green wire to the parking brake wire of the aftermarket

navigation radio (if applicable).

• Connect the

Blue/Pink wire to the VSS or speed sense wire of the aftermarket

navigation radio (if applicable).

• Connect the

Green/Purple wire to the reverse wire of the aftermarket navigation

radio (if applicable).

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to

test the radio.

RCA CONNECtiONS

• Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE

back up camera (if equipped).

• Connect the White and Red RCA to the audio "AUX in" of the aftermarket radio to

retain the OE 3.5mm jack (if equipped).

ASWC-1 (if installing)

After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the

AX-ADXSVI-CH3 and refer to the ASWC-1 instructions.

• Connect the

Gray wire to the right front positive speaker output of the

aftermarket radio.

• Connect the

Gray/Black wire to the right front negative speaker output of the

aftermarket radio.

• Connect the

Green wire to the radio’s left rear positive speaker output.

• Connect the

Green/Black wire to the radio’s left rear negative speaker output.

• Connect the

Purple wire to the radio’s right rear positive speaker output.

• Connect the

Purple/Black wire to the radio’s right rear negative speaker output.

The following wires are for the aftermarket radios that have navigation built in.

• Connect the

Light Green wire to the parking brake wire of the aftermarket

navigation radio (if applicable).

• Connect the

Blue/Pink wire to the VSS or speed sense wire of the aftermarket

navigation radio (if applicable).

• Connect the

Green/Purple wire to the reverse wire of the aftermarket navigation

radio (if applicable).

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to

test the radio.

RCA CONNECtiONS

• Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE

back up camera (if equipped).

• Connect the White and Red RCA to the audio "AUX in" of the aftermarket radio to

retain the OE 3.5mm jack (if equipped).

ASWC-1 (if installing)

After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the

AX-ADXSVI-CH3 and refer to the ASWC-1 instructions.