Atmel Evaluation Kit AT91SAM9M10-G45-EK AT91SAM9M10-G45-EK Data Sheet
Product codes
AT91SAM9M10-G45-EK
491
SAM9M10 [DATASHEET]
6355F–ATARM–12-Mar-13
indicates the maximum length of a timeguard period that the transmitter can handle in relation to the
function of the Baud Rate.
31.7.3.12
Receiver Time-out
The Receiver Time-out provides support in handling variable-length frames. This feature detects an idle condition
on the RXD line. When a time-out is detected, the bit TIMEOUT in the Channel Status Register (US_CSR) rises
and can generate an interrupt, thus indicating to the driver an end of frame.
on the RXD line. When a time-out is detected, the bit TIMEOUT in the Channel Status Register (US_CSR) rises
and can generate an interrupt, thus indicating to the driver an end of frame.
The time-out delay period (during which the receiver waits for a new character) is programmed in the TO field of
the Receiver Time-out Register (US_RTOR). If the TO field is programmed at 0, the Receiver Time-out is disabled
and no time-out is detected. The TIMEOUT bit in US_CSR remains at 0. Otherwise, the receiver loads a 16-bit
counter with the value programmed in TO. This counter is decremented at each bit period and reloaded each time
a new character is received. If the counter reaches 0, the TIMEOUT bit in the Status Register rises. Then, the user
can either:
the Receiver Time-out Register (US_RTOR). If the TO field is programmed at 0, the Receiver Time-out is disabled
and no time-out is detected. The TIMEOUT bit in US_CSR remains at 0. Otherwise, the receiver loads a 16-bit
counter with the value programmed in TO. This counter is decremented at each bit period and reloaded each time
a new character is received. If the counter reaches 0, the TIMEOUT bit in the Status Register rises. Then, the user
can either:
• Stop the counter clock until a new character is received. This is performed by writing the Control Register
(US_CR) with the STTTO (Start Time-out) bit at 1. In this case, the idle state on RXD before a new character is
received will not provide a time-out. This prevents having to handle an interrupt before a character is received
and allows waiting for the next idle state on RXD after a frame is received.
received will not provide a time-out. This prevents having to handle an interrupt before a character is received
and allows waiting for the next idle state on RXD after a frame is received.
• Obtain an interrupt while no character is received. This is performed by writing US_CR with the RETTO (Reload
and Start Time-out) bit at 1. If RETTO is performed, the counter starts counting down immediately from the
value TO. This enables generation of a periodic interrupt so that a user time-out can be handled, for example
when no key is pressed on a keyboard.
value TO. This enables generation of a periodic interrupt so that a user time-out can be handled, for example
when no key is pressed on a keyboard.
If STTTO is performed, the counter clock is stopped until a first character is received. The idle state on RXD before
the start of the frame does not provide a time-out. This prevents having to obtain a periodic interrupt and enables a
wait of the end of frame when the idle state on RXD is detected.
the start of the frame does not provide a time-out. This prevents having to obtain a periodic interrupt and enables a
wait of the end of frame when the idle state on RXD is detected.
If RETTO is performed, the counter starts counting down immediately from the value TO. This enables generation
of a periodic interrupt so that a user time-out can be handled, for example when no key is pressed on a keyboard.
of a periodic interrupt so that a user time-out can be handled, for example when no key is pressed on a keyboard.
Table 31-10.
Maximum Timeguard Length Depending on Baud Rate
Baud Rate
Bit time
Timeguard
Bit/sec
μs
ms
1 200
833
212.50
9 600
104
26.56
14400 69.4
17.71
19200
52.1
13.28
28800
34.7
8.85
33400
29.9
7.63
56000
17.9
4.55
57600
17.4
4.43
115200
8.7
2.21