Kaiser Nienhaus 380200 Drive with Toothed Belt Technology 380200 Data Sheet
Product codes
380200
7
02.2006 TR10A033-A RE
Dear Customer,
Thank you for choosing this quality product from our company.
Please keep these instructions safe for later reference!
Thank you for choosing this quality product from our company.
Please keep these instructions safe for later reference!
Please carefully read and follow these instructions. They provide
you with important information on the safe installation, operation
and correct care / maintenance of your garage door operator,
thus ensuring that this product will give you satisfaction for
many years to come.
you with important information on the safe installation, operation
and correct care / maintenance of your garage door operator,
thus ensuring that this product will give you satisfaction for
many years to come.
Please observe all our safety notes and warnings, specifically
headed ATTENTION, CAUTION or Note.
headed ATTENTION, CAUTION or Note.
1
IMPORTANT NOTES
ATTENTION
Installation, maintenance, repair and dismantling
of the garage door operator may only be carried
out by specialists.
Installation, maintenance, repair and dismantling
of the garage door operator may only be carried
out by specialists.
Note
The inspection log book and instructions for safe handling
and maintenance of the door system must be placed at
the disposal of the end user.
The inspection log book and instructions for safe handling
and maintenance of the door system must be placed at
the disposal of the end user.
1.1
Important safety instructions
CAUTION
Incorrect installation or handling of the operator
could result in serious injury. For this reason, it
is important to follow all the instructions in this
manual.
Incorrect installation or handling of the operator
could result in serious injury. For this reason, it
is important to follow all the instructions in this
manual.
This garage door operator is designed exclusively for
impulse operation of spring-balanced up-and-over and
sectional doors in the non-commercial sector. Use in
the commercial sector is not permitted!
Please observe the manufacturer's specifications regarding
the door and operator combination. Possible hazards as
defined in EN 12604 and EN 12453 are prevented by the
design itself and by carrying out installation in accordance
with our guidelines. Door systems used by the general
public and equipped with a single protective device, e.g.
force limit, may only be used when monitored.
impulse operation of spring-balanced up-and-over and
sectional doors in the non-commercial sector. Use in
the commercial sector is not permitted!
Please observe the manufacturer's specifications regarding
the door and operator combination. Possible hazards as
defined in EN 12604 and EN 12453 are prevented by the
design itself and by carrying out installation in accordance
with our guidelines. Door systems used by the general
public and equipped with a single protective device, e.g.
force limit, may only be used when monitored.
1.1.1
Warranty
We shall be exempt from our warranty obligations and
product liability in the event that the customer carries
out his own structural changes or undertakes improper
installation work or arranges for same to be carried out
without our prior approval and contrary to the installation
guidelines we have provided. Moreover, we shall accept no
responsibility for the inadvertent or negligent operation of
the operator and accessories nor for the improper main-
tenance of the door and its counterbalance mechanism.
Batteries and light bulbs are also not covered by the
warranty.
We shall be exempt from our warranty obligations and
product liability in the event that the customer carries
out his own structural changes or undertakes improper
installation work or arranges for same to be carried out
without our prior approval and contrary to the installation
guidelines we have provided. Moreover, we shall accept no
responsibility for the inadvertent or negligent operation of
the operator and accessories nor for the improper main-
tenance of the door and its counterbalance mechanism.
Batteries and light bulbs are also not covered by the
warranty.
Note
Should the garage door operator fail, a specialist must be
immediately entrusted with its inspection / repair.
Should the garage door operator fail, a specialist must be
immediately entrusted with its inspection / repair.
1.1.2
Checking the door / door system
The design of the operator is not suitable nor intended for
the opening and closing of heavy doors, i.e. doors that
are difficult or impossible to open and close manually.
Before installing the operator, it is therefore neces-
sary to check the door and make sure that it can
also be easily moved by hand.
To do this, raise the door approx. 1 metre and then let it
go. The door should retain this position, moving neither
up nor down. If the door moves in any of the two direc-
tions, there is a risk that the compensating springs are
defective or incorrectly adjusted. In this case increased
wear and malfunctioning of the door system can be
expected.
The design of the operator is not suitable nor intended for
the opening and closing of heavy doors, i.e. doors that
are difficult or impossible to open and close manually.
Before installing the operator, it is therefore neces-
sary to check the door and make sure that it can
also be easily moved by hand.
To do this, raise the door approx. 1 metre and then let it
go. The door should retain this position, moving neither
up nor down. If the door moves in any of the two direc-
tions, there is a risk that the compensating springs are
defective or incorrectly adjusted. In this case increased
wear and malfunctioning of the door system can be
expected.
CAUTION: Danger!
Do not attempt to change, re-adjust, repair or
move the compensating springs for the door's
counterbalance mechanism or their holders. The
springs are under considerable tension and can
cause serious injury. In addition, check the entire
door system (pivots, door bearings, cables,
springs and fastenings) for wear and possible
damage.
Check for signs of corrosion or fractures. The
door system may not be used if repair or adjust-
ment work needs to be carried out. Always
remember that a fault in the door system or a
misaligned door can also cause severe injury.
Do not attempt to change, re-adjust, repair or
move the compensating springs for the door's
counterbalance mechanism or their holders. The
springs are under considerable tension and can
cause serious injury. In addition, check the entire
door system (pivots, door bearings, cables,
springs and fastenings) for wear and possible
damage.
Check for signs of corrosion or fractures. The
door system may not be used if repair or adjust-
ment work needs to be carried out. Always
remember that a fault in the door system or a
misaligned door can also cause severe injury.
Note
Before installing the operator, and in the interests of your
own safety, make sure that any work needed on the door's
compensating springs is carried out by a qualified garage
door specialist. Only correct fitting and maintenance in
compliance with the instructions by a competent / specialist
company or a competent / qualified person ensures safe
and flawless operation of the system.
Before installing the operator, and in the interests of your
own safety, make sure that any work needed on the door's
compensating springs is carried out by a qualified garage
door specialist. Only correct fitting and maintenance in
compliance with the instructions by a competent / specialist
company or a competent / qualified person ensures safe
and flawless operation of the system.
1.2
Important instructions for safe installation
The specialist carrying out the work must ensure that
installation is conducted in compliance with the prevailing
national regulations on occupational safety and those
governing the operation of electrical equipment. In
the process, the relevant national guidelines must be
observed.
Possible hazards as defined in DIN EN 13241-1 are pre-
vented by the design itself and by carrying out installation
in accordance with our guidelines. Any further processing
must ensure that the national regulations governing the
operation of electrical equipment are complied with.
The specialist carrying out the work must ensure that
installation is conducted in compliance with the prevailing
national regulations on occupational safety and those
governing the operation of electrical equipment. In
the process, the relevant national guidelines must be
observed.
Possible hazards as defined in DIN EN 13241-1 are pre-
vented by the design itself and by carrying out installation
in accordance with our guidelines. Any further processing
must ensure that the national regulations governing the
operation of electrical equipment are complied with.
1.2.1 Before installing the garage door operator, check
that the door is in a flawless mechanical condition and
is correctly balanced, so that it can be easily moved by
hand (EN 12604). Further check whether the door opens
and closes in the proper manner (see section 1.1.2).
In addition, any of the door's mechanical locks and
latches not needed for power operation of the garage
door should be immobilized. Included here in particular
are the latching mechanisms of the door lock (see section
3.2.1/3.2.2).
The garage door operator is designed for use in dry
buildings and therefore may not be installed outdoors.
The garage ceiling must be constructed in such a way
as to guarantee safe, secure anchoring of the operator.
In the case of ceilings that are too high or too lightweight,
the operator must be attached to additional braces.
is correctly balanced, so that it can be easily moved by
hand (EN 12604). Further check whether the door opens
and closes in the proper manner (see section 1.1.2).
In addition, any of the door's mechanical locks and
latches not needed for power operation of the garage
door should be immobilized. Included here in particular
are the latching mechanisms of the door lock (see section
3.2.1/3.2.2).
The garage door operator is designed for use in dry
buildings and therefore may not be installed outdoors.
The garage ceiling must be constructed in such a way
as to guarantee safe, secure anchoring of the operator.
In the case of ceilings that are too high or too lightweight,
the operator must be attached to additional braces.
➤
E N G L I S H