Weslo WLAW35010 Owner's Manual
5
1. Read the instructions at the top of page 4
before beginning assembly.
Identify the Left Leg (4) and the Left Brace (2),
which are marked with stickers. Next, identify the
Left Upright (34), which has a serial number decal
attached to it.
which are marked with stickers. Next, identify the
Left Upright (34), which has a serial number decal
attached to it.
Apply a small amount of the included grease to
the axle on the Left Leg (4). Slide the Link Arm
Plate (6), the left Upright (34), and the Left Brace
(2) onto the axle. Make sure that all parts are
turned exactly as shown. Tap a 19mm Axle Cap
(17) onto the axle.
the axle on the Left Leg (4). Slide the Link Arm
Plate (6), the left Upright (34), and the Left Brace
(2) onto the axle. Make sure that all parts are
turned exactly as shown. Tap a 19mm Axle Cap
(17) onto the axle.
Assemble the Right Leg (5), the other Upright
(34), and the Right Brace (3) in the same way.
(34), and the Right Brace (3) in the same way.
2. Attach the Lower Crossbar (1) to the left Upright
(34) with two M10 x 54mm Carriage Bolts (35)
and two M10 Nylon Locknuts (32) as shown.
Make sure that the Lower Crossbar is oriented
so that the threaded axle and the SPACE
SAVER decal are in the positions shown. Do
not tighten the Nylon Locknuts yet.
and two M10 Nylon Locknuts (32) as shown.
Make sure that the Lower Crossbar is oriented
so that the threaded axle and the SPACE
SAVER decal are in the positions shown. Do
not tighten the Nylon Locknuts yet.
Insert the lower end of the Left Brace (2) into the
Right Brace (3). Tighten an M4 x 16mm Flange
Screw (28) into the Right Brace.
Right Brace (3). Tighten an M4 x 16mm Flange
Screw (28) into the Right Brace.
Attach the Lower Crossbar (1) to the right Upright
(34) with two M10 x 54mm Carriage Bolts (35)
and two M10 Nylon Locknuts (32). Do not tighten
the Nylon Locknuts yet.
(34) with two M10 x 54mm Carriage Bolts (35)
and two M10 Nylon Locknuts (32). Do not tighten
the Nylon Locknuts yet.
3. Lay the Rocker Arm (9) on the floor in the position
shown. Apply a small amount of the included
grease to the axles on the Rocker Arm.
grease to the axles on the Rocker Arm.
Identify the Right Link Arm (31), which is marked
with a sticker. Slide the Right Link Arm onto the
indicated axle on the Rocker Arm (9). Slide the
Left Link Arm (7) onto the other axle. Make sure
that both Link Arms are turned exactly as
shown, with the four Link Arm Bushings (14)
on the sides shown. Tap a 9.5mm Axle Cap (15)
onto each axle.
with a sticker. Slide the Right Link Arm onto the
indicated axle on the Rocker Arm (9). Slide the
Left Link Arm (7) onto the other axle. Make sure
that both Link Arms are turned exactly as
shown, with the four Link Arm Bushings (14)
on the sides shown. Tap a 9.5mm Axle Cap (15)
onto each axle.
1
3
14
14
14
Grease
Grease
31
7
9
15
15
32
1
35
Axle
34
SPACE
SAVER
SAVER
Decal
35
34
32
2
3
28
4
Grease
5
34
Serial
Number
Decal
34
2
3
17
17
6
Tube must extend
on this side
Tube must extend
on this side
2