Blaupunkt AUSTIN CD41 User Manual
E-3
ENGLISH
FRAN
Ç
AIS
ESP
A
Ñ
OL
POR
TUGU
Ê
S
11
DISC SELECT button
Select the desired CD in CDC (CD changer) mode.
Select the desired CD in CDC (CD changer) mode.
12
SC/PS button
Scan tuning. Preset scan tuning. Scan play in CD/CDC
mode.
Scan tuning. Preset scan tuning. Scan play in CD/CDC
mode.
13
AUD button
Audio control selector; Bass, Treble, Loudness, Balance
& Fader.
& Fader.
14
Dial
Adjusts the volume level/bass/treble/balance/fader.
Storing the station names. Select alfa-numeric charac-
ters.
ters.
15
Infrared Sensor (behind acrylic facia)
Permits wireless remote control of AM/FM/CD and CD
changer with optional credit card style remote. See Dealer
for Details.
changer with optional credit card style remote. See Dealer
for Details.
Turning the power On/Off
Press the
PWR
to turn on or off the unit.
Tip
When you turn on the unit, “HELLO” will be displayed then
“WELCOME” will momentarily be displayed before actual
power on.
When you turn off the unit, “SEE YOU” will be displayed then
“GOOD-BYE” will momentarily be displayed before actual
power off.
You can edit these messages. (See “Turn on/off message
edit”)
When you turn on the unit, “HELLO” will be displayed then
“WELCOME” will momentarily be displayed before actual
power on.
When you turn off the unit, “SEE YOU” will be displayed then
“GOOD-BYE” will momentarily be displayed before actual
power off.
You can edit these messages. (See “Turn on/off message
edit”)
Volume Level Control and Memory
Rotate the dial to adjust the volume.
It is also possible to set the maximum volume for when the
power is switched on by following the procedure explained
below.
It is also possible to set the maximum volume for when the
power is switched on by following the procedure explained
below.
1.
Turn the dial until it is set at the required volume.
Volume down
Volume up
2.
Press the
PWR
for two or more seconds. The power will
be switched off and the current volume level recorded.
Muting the sound
Press
MUTE / SENS
.
“ MUTE ” appears on the display window.
To restore the previous volume level, press
To restore the previous volume level, press
MUTE / SENS
again.
Setting the Clock
The clock uses a 12-hour display system. (factory set)
1.
Turn the ignition key to the ON position.
2.
Press the
PWR
to turn on the unit.
3.
Repeatedly press the
DISP
to display “ CLOCK 12 ”.
4.
Rotate the dial within 5 seconds to select the 12 or 24-
hour time mode. Each time you rotate the dial, the mode
changes or toggles as follows :
hour time mode. Each time you rotate the dial, the mode
changes or toggles as follows :
CLOCK 24
CLOCK 12
5.
Repeatedly press the
DISP
to display “ CLK ADJ ”.
A.
Press the
MUTE / SENS
within 5 seconds to flash the hour digit.
B.
Rotate the dial to set the hour digit.
C.
Press the
MUTE / SENS
to flash the minute digit.
D.
Rotate the dial to set the minute digit.
6.
Press the
DISP
momentarily to complete the Clock set-
ting mode.
Note
If you make no button input or dial operation in 20 seconds,
the Clock setting mode will turn off automatically.
If you make no button input or dial operation in 20 seconds,
the Clock setting mode will turn off automatically.
Ignition-off Clock Recall
The display will illuminate showing the time and then auto-
matically shut off after 5 seconds.
Press the
matically shut off after 5 seconds.
Press the
DISP
while the ignition switch is in the “ OFF ” posi-
tion.
General Operations
AUSTIN CD41
01.3.22, 1:45 PM
3