Whirlpool WMH76719C Owner's Manual

Observe all governing codes and ordinances.

■

A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a 
fuse or circuit breaker.

■

A time-delay fuse or time-delay circuit breaker.

■

A separate circuit serving only this microwave oven.

The Clock is a 12-hour (12:00-11:59) or 24-hour (0:00-23:59) clock. 
Touch OPTIONS/CLOCK to reach Clock submenu, and follow the 
prompts to set the Clock. Clock format (12 hours with AM and PM or 
24 hours) may also be set in the Clock submenu.

With the microwave oven in standby mode, touch the Timer control, 
enter time, then touch the Timer control or the Start control. Cook 
functions may be entered while the Timer is counting down. To cancel 
timer, touch Timer control while the Timer countdown is active in the 
display.

Activate to avoid unintended start. Touch and hold the Cancel control 
for about 3 seconds until 2 tones sound and padlock icon appears in 
the display. Repeat to unlock control.

Twelve options/settings may be adjusted: 1-Clock; 2-Scrolling Speed; 
3-Sound; 4-Language (English or French); 5-Energy Save; 6-Auto 
Adapt Fan; 7-Filter Alert; 8-30 Minute Fan Timer; 9-Light Timer; 
10-Temp Calibration (on convection models); 11-Demo Mode; 
12-Factory Reset.

Various speeds, ranging from high to low, and off. Comes on 
automatically as cooling fan during any cook function.

30 Minute Fan Timer: Set vent fan to run for exactly 30 minutes, or to 
run for only 30 minutes more (off after 30 minutes). The vent fan may 
be turned off at any time using the Vent Fan control. Touch OPTIONS/
CLOCK to reach the 30 Minute Fan Timer submenu, and select the 
setting.

Auto Vent Fan: To keep the microwave oven from overheating, the 
auto vent fan will automatically turn on at high speed if the temperature 
from the range or cooktop below the microwave oven gets too hot. 
When this occurs, the vent fan cannot be turned off. “FAN ON for heat 
circulation” appears in the display.

Set the cooktop light to turn on and off at certain times. Touch 
OPTIONS/CLOCK to reach the Light Timer submenu, and follow the 
prompts to set the light on time and light off time in hours and minutes, 
or to cancel Light Timer.

NOTE: Light Timer uses 12-hour clock only.

Reset the filter status after replacing and/or cleaning the filters. Touch 
OPTIONS/CLOCK to reach the Filter Alert submenu, and activate 
reset.

Programming tones and signals. Key beep tones may be turned off, or 
all tones (including end-of-function signals) may be turned off. Touch 
OPTIONS/CLOCK to reach the Sound submenu, then follow the 
prompts to turn off or on the programming tones or all tones.

Scroll speed of the text may be adjusted. Touch the OPTIONS/CLOCK 
to reach the Scrolling Speed submenu, and follow the prompts to set 
speed.

Activate to practice using the control without actually turning on the 
magnetron. Touch OPTIONS/CLOCK to reach the Demo Mode 
submenu, the follow the prompts to activate. The DEMO icon will light 
up in the display. Repeat to deactivate.

■  

For all cord connected appliances:
The microwave oven must be grounded. In the event of 
an electrical short circuit, grounding reduces the risk of 
electric shock by providing an escape wire for the electric 
current. The microwave oven is equipped with a cord 
having a grounding wire with a grounding plug. The plug 
must be plugged into an outlet that is properly installed 
and grounded.

WARNING: 

Improper use of the grounding plug can 

result in a risk of electric shock. Consult a qualified 
electrician or serviceman if the grounding instructions are 
not completely understood, or if doubt exists as to whether 
the microwave oven is properly grounded. 

Do not use an extension cord. If the power supply cord is 
too short, have a qualified electrician or serviceman install 
an outlet near the microwave oven.

This device complies with Part 18 of the FCC Rules.