APC 9000 User Manual
34006452EN/AC
- Page 58
"Monitor" alphanumeric display
9.12 Display system configuration
Display system configuration
This function may be accessed from the initial screen. Press the "*" button, followed by the "V" button in less than one second.
Note:
– ensure that two "Monitor" or "Tele Monitor" units do not receive the same number;
– ensure that two "Monitor" or "Tele Monitor" units do not receive the same number;
– only one master "Tele Monitor" may be installed on the display network;
– this function may be accessed only with a password.
This function may be accessed from the initial screen.
Press the "*" button, followed by the "V" button in less
than one second.
Press the "*" button, followed by the "V" button in less
than one second.
Enter the password (a combination of four buttons
among the control panel buttons). If the password
is incorrect, the system displays the following screen
for a few seconds:
among the control panel buttons). If the password
is incorrect, the system displays the following screen
for a few seconds:
INCORRECT
PASSWORD
then automatically returns to the initial screen.
Selection of the type of display: local ("Monitor")
or distant ("Tele Monitor"). If the display is distant,
the local buzzer is deactivated.
or distant ("Tele Monitor"). If the display is distant,
the local buzzer is deactivated.
Selection of display role on the network: master
(only one display may be the master) or slave.
(only one display may be the master) or slave.
Selection of the slave display number (multi-display installation)
from 1 to 10.
from 1 to 10.
Selection of the numbers of the cubicles that the display
must control. Ten cubicle numbers are successively presented.
Select "yes" if the display is to control the cubicle or "no"
if it does not control the cubicle or if the cubicle does not exist.
Confirm using the "*" button. The system goes on to the next
cubicle number. Following confirmation of the last cubicle
number, the system automatically returns to the initial screen.
must control. Ten cubicle numbers are successively presented.
Select "yes" if the display is to control the cubicle or "no"
if it does not control the cubicle or if the cubicle does not exist.
Confirm using the "*" button. The system goes on to the next
cubicle number. Following confirmation of the last cubicle
number, the system automatically returns to the initial screen.
Selection of the numbers of the slave displays controlled
by the master display. Ten display number are successively
presented. Select "yes" if the master display is to control
the slave display or "no" if it does not control the display
or if the display does not exist. Confirm using the "*" button.
The system goes on to the next display.
by the master display. Ten display number are successively
presented. Select "yes" if the master display is to control
the slave display or "no" if it does not control the display
or if the display does not exist. Confirm using the "*" button.
The system goes on to the next display.
Selection of the numbers of the cubicles controlled
by the display. Eight cubicle number are successively
presented. Select "yes" if the display is to control the cubicle
or "no" if it does not control the cubicle or if the cubicle does
not exist. Confirm using the "*" button. The system goes
on the next screen.
by the display. Eight cubicle number are successively
presented. Select "yes" if the display is to control the cubicle
or "no" if it does not control the cubicle or if the cubicle does
not exist. Confirm using the "*" button. The system goes
on the next screen.
Confirmation as to whether the installation is equipped
with a giant screen. Following confirmation using
the "*" button, the system automatically returns
to the initial screen.
with a giant screen. Following confirmation using
the "*" button, the system automatically returns
to the initial screen.
PASSWORD ?
=
DISPLAY = MASTER
>=SELECT =CONFIRM.
*
DISPLAY NUMBER =
>=SELECT =CONFIRM.
*
CUBICLE N° = YES
>=SELECT =CONFIRM.
*
*
initial screen
V
if display
is master
*
initial screen
DISPLAY N° = YES
>=SELECT =CONFIRM.
CUBICLE N° = YES
>=SELECT =CONFIRM.
*
GIANT DISPLAY =YES
>=SELECT =CONFIRM.
initial screen
*
if display
is slave
*
DISPLAY = LOCAL
>=SELECT =CONFIRM.