Regency F37-NG Manual De Usuario

10

F37 Regency

®

 Rear Flued Room Sealed Freestanding Gas Heater

*Diagram 2:  Local codes or regulations may 
require different clearances.

You will require the following components with your new Regency

®

 Rear Flued Room Sealed Freestanding Gas Stove. Please review your product 

to make sure you have everything you need. In the event that you are missing any part, contact your dealer. 

Minimum components for a Horizontal Installation: 
946-112 

Horizontal Termination Kit which includes:

 

1 

6-5/8" dia. x 18" (168mm dia. x 457mm) Black Pipe 

 

1 

4" dia. x 18" (102mm dia. x 457mm) Aluminum Flue

 

1 

Astro Riser Vent Terminal

 

1 

Wall Penetration Heat Shield for Heat Sensitive walls

  

(Wall 

Thimble) 

(2 

pcs)

 1 

Decorative 

Wall 

Trim 

(Black)

 1 

Tube 

Mill-Pac

  

Screws

Optional Components:
946-204  45

o

 Elbow - 6-5/8" (168mm) Black pipe 

  

and 

4" 

(102mm) 

Aluminum 

Flue

946-205 

 

Vinyl Siding Shield for Riser Vent

  

Terminal

946-208/P  

Flue 

Guard

940  

Square 

Wall 

Thimble 

Cover*

942  

Wall 

Penetration

  

Heat 

Shield*

* Simpson Dura-Vent  components
 

1)  Set the unit in its desired location. Check to 

determine if wall studs are in the way when 
the fl ueing system is attached. If this is the 
case, you may want to adjust the location 
of the unit.

2)  Assemble the desired combination of pipe 

and elbow to the appliance adapter with pipe 
seams oriented down. Offset the pipe seams 
as double seams in one place will cause the 
outer pipe to take an oval shape. Kit comes 
complete with 18" (457mm) of straight fl ue 
- 6-5/8" (168mm) dia. black outer pipe and 
4" (102mm) dia. inner fl ue. 

3)  With the pipe attached to the stove, slide 

the stove into its correct location, and mark 
the wall for a  

9-1/2" (241mm) (inside 

dimensions) round hole. The center of the 
round hole should line up with the centerline 
of the horizontal pipe, as shown in diagram 
1. Cut and frame the 9-1/2 (241mm) round 
hole in the exterior wall where the fl ue will 
be terminated. If the wall being penetrated is 
constructed of non-combustible material, i.e. 
masonry block or concrete, a  7" (178mm) 
diameter hole is acceptable.

 

 a)  The horizontal run of fl ue should have 

a 1/4 inch (6mm) rise for every 1 foot 
(305mm) of run towards the termination. 
Never allow the fl ue to run downward. 
This could cause high temperatures and 
may present the possibility of a fi re.

 b)  The location of the horizontal fl ue ter-

mination on an exterior wall must meet 
all local and national building codes, 
and must not be blocked or obstructed. 
See the diagram in the "External  Flue 
Termination Locations" section.

 c)  Snorkel Terminations:
 

 

For installations requiring a vertical rise 
on the exterior of the building, Astro Riser 
Vent Terminations as shown in Dia. 2 
is available. Follow the same installa-
tion procedures as used for standard 
Horizontal Termination. 

 

 

NEVER install the Astro Riser vent upside 
down.