Electrolux E30GC70FSS Guía Del Usuario
13
Surface Burner
Grate
Surface Burner
Caps
Surface Burner
Heads
CA
CA
CA
CA
CAUTION
UTION
UTION
UTION
UTION
- Use caution when replacing the burner head so the electrode is not damaged. A damaged
electrode may cause a delayed ignition or prevent the burner from igniting
- Any additions, changes or conversions required in order for this appliance to perform
satisfactorily must be made by a qualified service technician.
Figure 1
General Care & Cleaning
General Care & Cleaning
General Care & Cleaning
CLEANING THE BURNER GRATES, BURNER CAPS AND
BURNER HEADS
BURNER HEADS
The Burner Grates, Burner Caps and Burner Heads should be routinely cleaned. Keeping
the burner ports clean will prevent improper ignition and an
uneven flame.
the burner ports clean will prevent improper ignition and an
uneven flame.
Refer to the following instructions:
To Remove and Replace the Surface Burner Grate,
Surface Burner Cap and Surface Burner Head - Remove
in the following order; (1st) Surface Burner Grate, (2nd) Surface
Burner Cap, (3rd) Surface Burner Head (See Figure 1).
Surface Burner Cap and Surface Burner Head - Remove
in the following order; (1st) Surface Burner Grate, (2nd) Surface
Burner Cap, (3rd) Surface Burner Head (See Figure 1).
Reverse the procedure above to replace the Surface Burner
Cap, Surface Burner Head and Surface Burner Grate. Do not
remove any burner parts from the cooktop until the
burner parts have completely cooled and are safe to
handle. Do not operate the surface burners without the
Surface Burner Caps, Surface Burner Heads and Surface
Burner Grates properly in place.
Cap, Surface Burner Head and Surface Burner Grate. Do not
remove any burner parts from the cooktop until the
burner parts have completely cooled and are safe to
handle. Do not operate the surface burners without the
Surface Burner Caps, Surface Burner Heads and Surface
Burner Grates properly in place.
To Clean the Burner Caps, Burner Heads and Burner
Grates - Use a soap-filled scouring pad or a mild abrasive
cleaner to clean the surface burner caps and surface burner
heads. The Grates are designed to be Dishwasher safe for
cleaning. The ports (or slots) around the burner heads must be
routinely cleaned. If residue still remains in these ports, use a
small-gauge wire or needle to clean the slots or holes being
careful not to damage the electrode. For proper flow of gas and ignition of the burner—DO
NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO
ENTER THE GAS ORIFICE HOLDER OPENING. ALWAYS make sure that the surface
burner cap, the surface burner head and the surface burner grate are properly in place
whenever a surface burner is in use.
Grates - Use a soap-filled scouring pad or a mild abrasive
cleaner to clean the surface burner caps and surface burner
heads. The Grates are designed to be Dishwasher safe for
cleaning. The ports (or slots) around the burner heads must be
routinely cleaned. If residue still remains in these ports, use a
small-gauge wire or needle to clean the slots or holes being
careful not to damage the electrode. For proper flow of gas and ignition of the burner—DO
NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO
ENTER THE GAS ORIFICE HOLDER OPENING. ALWAYS make sure that the surface
burner cap, the surface burner head and the surface burner grate are properly in place
whenever a surface burner is in use.
1st
2nd
3rd
Orifice
Electrode
Surface
Burner
Head
Surface
Burner
Cap
Surface Burner Grate
THE COOKTOP IS NOT REMOVABLE. Do not attempt to remove or lift the cooktop.