Crimestopper Security Products CS-880 OEM Manual De Usuario
PROGRAMMING
TO TURN A FEATURE ON: Once you are at the desired option number,
turn the Ignition key OFF then back ON. After a few seconds, the siren
will chirp and the lights will flash once to indicate the feature is ON. (See
chart below for feature values)
turn the Ignition key OFF then back ON. After a few seconds, the siren
will chirp and the lights will flash once to indicate the feature is ON. (See
chart below for feature values)
TO TURN A FEATURE OFF: Once you are at the desired option
number, turn the Ignition key OFF/ON/OFF/ON. After a few seconds, the
siren will chirp two times and the lights will flash two times to indicate the
feature is OFF. (See chart below for feature values)
number, turn the Ignition key OFF/ON/OFF/ON. After a few seconds, the
siren will chirp two times and the lights will flash two times to indicate the
feature is OFF. (See chart below for feature values)
Option
#
Option Description
ON
(Default)
OFF
1
(+ or -) Door Lock Input
Signal
Signal
NEGATIVE
POSITIVE
2
(+ or -) Disarm Validating
Input Signal
Input Signal
NEGATIVE
POSITIVE
3
Disarm Level
MODE 1
MODE 2
4
Door Open Warning
25 Seconds
NONE
5
Silent Arm/Disarm
With Chirps
NO Chirps
6
Passive Arming
ON
OFF
7
Shock sensor Test Mode
OPTION DESCRIPTIONS (SEE CHART ABOVE)
1. DOOR LOCK INPUT SIGNAL:
This option controls whether the unit senses (+) Positive or (-) Negative
Lock and Unlock signal to arm and disarm the system. The Factory
Default setting is ON (Negative).
This option controls whether the unit senses (+) Positive or (-) Negative
Lock and Unlock signal to arm and disarm the system. The Factory
Default setting is ON (Negative).
2. DISARM VALIDATING INPUT SIGNAL:
This option controls whether the unit senses (+) Positive or (-) Negative
Disarm Validating Signal. I.e. Flashing lights, Horn, etc. The validation
signal is used for a higher security level when disarming the system.
When the 880 is configured for MODE 2 The unit will have to sense an
Unlock pulse AND a (+ or -) Validation signal before disarming.
This option controls whether the unit senses (+) Positive or (-) Negative
Disarm Validating Signal. I.e. Flashing lights, Horn, etc. The validation
signal is used for a higher security level when disarming the system.
When the 880 is configured for MODE 2 The unit will have to sense an
Unlock pulse AND a (+ or -) Validation signal before disarming.
3. DISARM MODE:
This option controls how the system is disarmed.
MODE 1: (Factory Default) This mode allows the system to be disarmed
by sensing an (+/-) Unlock pulse. Anytime the Unlock Button on the
Factory remote is pressed, the system will disarm. (Triggered or
otherwise)
MODE 2: This mode allows the unit to disarm only when the system
senses an Unlock Pulse AND a Validation pulse. This is higher security
although more wiring is required.
This option controls how the system is disarmed.
MODE 1: (Factory Default) This mode allows the system to be disarmed
by sensing an (+/-) Unlock pulse. Anytime the Unlock Button on the
Factory remote is pressed, the system will disarm. (Triggered or
otherwise)
MODE 2: This mode allows the unit to disarm only when the system
senses an Unlock Pulse AND a Validation pulse. This is higher security
although more wiring is required.
PROGRAMMING
4. DOOR OPEN WARNING
This setting changes the delay time in which the alarm system begins to
monitor the Door, Hood, or Trunk Zones. This is helpful on vehicles with
a delayed dome light to prevent the alarm from giving warning chirps due
to the vehicle’s dome light staying on. Factory Default setting is 25 Sec.
This setting changes the delay time in which the alarm system begins to
monitor the Door, Hood, or Trunk Zones. This is helpful on vehicles with
a delayed dome light to prevent the alarm from giving warning chirps due
to the vehicle’s dome light staying on. Factory Default setting is 25 Sec.
5. SILENT ARMING /DISARMING (NO CHIRPS)
With this feature, the system can be programmed to Arm and Disarm
without the siren/horn chirp. Flashing parking lights will be the only
Arm/Disarm confirmation. The Factory Default setting is OFF.
With this feature, the system can be programmed to Arm and Disarm
without the siren/horn chirp. Flashing parking lights will be the only
Arm/Disarm confirmation. The Factory Default setting is OFF.
6. PASSIVE ARMING
This option controls the Passive (Automatic) Arming feature. If ON,
arming will occur 30 Seconds after the ignition is turned off and the last
door has been closed. The LED will begin flashing rapidly while counting
down. If a door is reopened, the system will wait (LED solid) for the door
or zone to close before arming. The unit will chirp once and flash the
lights once. Doors will lock if passive locking is selected. Factory default
setting is ON.
This option controls the Passive (Automatic) Arming feature. If ON,
arming will occur 30 Seconds after the ignition is turned off and the last
door has been closed. The LED will begin flashing rapidly while counting
down. If a door is reopened, the system will wait (LED solid) for the door
or zone to close before arming. The unit will chirp once and flash the
lights once. Doors will lock if passive locking is selected. Factory default
setting is ON.