Fujifilm s602 Manuel D’Utilisation

86

e

If you think the camera is faulty, check the following once more

The camera won’t switch
on.

i

The batteries are exhausted.

i

The batteries are loaded the wrong way
round.

i

The AC power adapter is not connected
correctly.

i

Load new or fully charged batteries.

i

Reload the batteries correctly

i

Reconnect the adapter correctly and plug
the adapter plug into the mains power outlet.

Batteries run out quickly.

i

You are using the camera in extremely
cold conditions.

i

The battery terminals are soiled.

i

The battery terminals were soiled when
the batteries were charged.

i

The batteries were charged after having
not been used for a long period.

i

The rechargeable batteries have reached
the end of their operating lives.

i

Put the batteries in your pocket or another
warm place to heat them and then load
them into the camera just before you take
a picture. Note that alkaline batteries
cannot be used at very low temperatures.

i

Remove the batteries from the camera and
wipe the battery terminals with a clean, dry
cloth before reloading the batteries.

i

Wipe the battery terminals with a clean,
dry cloth before charging.

i

Due to their nature, the batteries may not
be fully charged. Charge and use the
batteries several times to restore them to
normal operation.

i

Load new fully charged batteries.

Power cuts out during
operation.

i

The batteries are exhausted.

i

Load new or fully charged batteries.

Focusing is slow.

i

The SET ADAPTER RING menu in the
“SET–UP” menu is “YES”.

i

The external AF sensor is dirty.

i

If you are not using an adapter, select the
“NO” setting.

i

Use a blower brush to brush away any
dust and then gently wipe the sensor with
a soft, dry cloth.

I can’t set the camera to
Macro (close-up) mode.

i

The camera is set to Movie mode or to
the Scenery, Sport or Night Scene setting
in Scene Position mode.

i

Change the photography mode or select
Monochrome in Scene Position mode.

I can’t select continuous
shooting.

i

Voice memo is selected.

i

Multi-exposure mode is selected.

i

Set voice memo to “OFF”.

i

Set multi-exposure mode to “OFF”.

When the resolution is set
to 

1

, I can only select

NORMAL or FINE.

i

Long period continuous shooting is
selected.

i

Select a continuous shooting mode other
than Long period continuous shooting.

When the resolution is set
to 

1

, I can only select

NORMAL.

i

The sensitivity (ISO) is set to 800 or 1600
(high-sensitivity photography).

i

Set the sensitivity (ISO) to 400 or lower.

I can’t use the flash.

i

The flash is not popped up.

i

You pressed the shutter button while the
flash was charging.

i

The batteries are exhausted.

i

The camera is set to Scenery in Scene
Position mode

i

Pop up the flash.

i

Wait until the flash has finished charging
before pressing the shutter button.

i

Load new or fully charged batteries.

i

Select another Scene Position or change
the photography mode.

I can’t set the self-timer.

i

Long period or Final 5-frame continuous
shooting is selected.

i

Select a continuous shooting mode other
than Long period or Final 5-frame or set
continuous shooting to “OFF”.

I can’t set a voice memo.

i

Continuous shooting is selected.

i

Set continuous shooting to “OFF”.

No photograph is taken
when I press the shutter
button.

i

The batteries are exhausted.

i

The Auto Power Off function has switched
the camera off.

i

There is no media in the camera.

i

The media is not formatted.

i

The media is full and no further data can
be recorded.

i

The SmartMedia contact area (the gold-
colored area) is soiled.

i

The SmartMedia is write-protected.

i

The media is damaged (CARD ERROR).

i

Load new or fully charged batteries.

i

Switch the camera on.

i

Load a media.

i

Format the media.

i

Erase some unwanted frames or load a
new media.

i

Wipe the SmartMedia contact area with a
clean, dry cloth.

i

Remove the write-protection (Peel off the
write-protect sticker).

i

Use a different media.