Clarion CZ703E Manuel D’Utilisation

English

15

CZ703E

ERROR 3

Disc is inserted incorrectly.

Eject the disc then reload it properly.

The disc format is not supported.

Try another disc.

ERROR 5

This is a failure of deck’s mechanism.

Consult your store of purchase.

If an error occurs, one of the following displays is displayed. 

Take the measures described below to solve the problem.

If an error display other than the ones described above appears, press the 

 button. If the 

problem persists, turn off the power and consult your store of purchase.

*   When the 

 button is pressed, frequencies of radio stations, titles, etc. stored in 

memory are cleared.

USB device cannot 
be inserted.

The USB device has been 
inserted with wrong direction.

Reversing the connection direction of the USB 
device, try it again.

The USB connector is broken.

Replace with a new USB device.

USB device is not 
recognized.

The USB device is damaged.

Disconnect the USB device and reconnect. If the 
device is still not recognized, try replacing with a 
different USB device.

Connectors are loose.

No sound heard with 
the display “

” 

shown.

No MP3/WMA file is stored in the 
USB device.

Store these files properly in the USB device.

Sound skips or is 
noisy.

MP3/WMA files are not encoded 
properly.

Use MP3/WMA files encoded properly.

Cannot pair the 
Bluetooth enabled 
device with the car 
audio system.

The device does not support the 
profiles required for the system.

Use another device to connect.

The Bluetooth function of the 
device is not enabled.

Refer to the user manual of the device for how to 
enable the function.

The audio quality 

is poor after 

connection with a 

Bluetooth-enabled 

device.

The internal microphone gain is 

not set correctly.

Adjust  the  gain  of  the  internal  microphone  in 
System Setup.

The external microphone is not set 

correctly nor properly positioned.

Adjust the gain and position of the external 

microphone.
For example, stick the microphone onto the 

dashboard so it is close to the driver.

Frequency range: 87.5-108.0MHz

Usable sensitivity: 8dBf

Frequency response: 30Hz-15kHz

Stereo separation: 30dB(1kHz)

Signal/noise ratio: >55dB

Frequency range: 531- 1602kHz
Usable sensitivity (S/N=20dB): 30dBμ

Frequency range: 153-279kHz
Usable sensitivity (S/N=20dB): 34dBμ

System: Disc digital audio system

Frequency response: 20Hz-20kHz

Signal/noise ratio: >94dB

Total harmonic distortion: Less than 0.1% (1kHz)
Channel separation: >60dB

MP3 sampling rate: 8 kHz to 48 kHz

MP3 bit rate: 8 kbps to 320 kbps / VBR

WMA bit rate: 8 kbps to 320 kbps

Logical format: ISO9660 level 1,2

                         Joliet file system

Specification: USB 1.0/2.0

Playable audio format:

  

MP3(.mp3): MPEG 1/2/Audio Layer-3

  

WMA(.wma): Ver 7/8/9.1/9.2

Specification: Bluetooth Ver. 2.0+EDR

Profile: 

  

HFP (Hands-free Profile)

  

PBAP(Phone Book Access Profile)

  

A2DP (Advanced Audio Distribution Profile)

  

AVRCP (AV Remote Control Profile)

Send/Receive Sensitivity: Class 2

Maximum power output:

  

200W (50W x 4)

Speaker impedance: 4  (4 to 8  allowable)

Audio input sensitivity:

  

High: 320mV (at 2.5V output)

  

Mid: 650mV (at 2.5V output)

  

Low: 1.3V (at 2.5V output)

  

(input impedance 10 k  or greater)

Aux-in level: ≤2V

Power supply voltage: 

  

14.4VDC (10.8 to 15.6V allowable), 

  

negative ground

Pre-Amp output voltage: 

  

5.0V (CD play mode: 1kHz, 0dB, 10k  load) 

Fuse: 15A

Dimensions of the Main Unit: 

  

188mm Width × 58mm Height × 190mm Depth

Weight of the Main Unit: 1.44kg

Dimensions of the Remote Control unit:

  

 43mm Width  × 11mm Height × 113mm Depth

Weight of the Remote Control Unit:

  

45g (including battery)

•    Specifications and design are subject to change 

without notice for further improvement.

170mm

188mm

58mm

1

6

3

mm

1

4

m

m

46mm

50mm

178mm

1

9

0

m

m