Whirlpool 15080000 Manuel D’Utilisation

Document ID:15080000

Rev: E

Technical Support: 800-626-6912

Page 11 of 20

Pedicure Spa Specifications

*Hot and cold w ater supply lines required (hot and cold shut offs may be installed under pedicure spa base)

*Drain installation:

References noted on page 9, standard unit comes w ith drain pump.

Overall dimensions w ithout accessories, seat upright: 60"L (152cm) x 44"W (112cm) x 60"H (152c m) *

Overall dimensions, seat upright, both armrests open w \ cup holders exposed:

60”L (152cm) x 44”W (112cm) x 60”H (152c m)

Without accessories, seat collapsed, both arms closed:

(Shipping position): 60”L (152c m) x 32”W (81cm) x 37”H (94c m)*

Maximum area required for full chair and armrest movement:

77”L (196cm) x 44”w (112cm) x 60”H (152cm)*

Shipping dimensions:

65”L (165cm) x 33”W (84cm) x 65”H (165c m)*

Empty weight:

179 lbs. (81kg)*

Shipping weight:

245 lbs. (102kg)*

Capacity of basin:

Will hold up to 6.0 U.S. Gallons; w ater level markings at 5.5 U.S. gallons

Whirlpool pump motor:

110V:

1/6 HP, 110V, 60Hz (alternate voltages available)

220V:

1/6 HP, 220V, 50/60Hz

Seat and back motors:

24V DC Linear Actuators. Spa requires 16” (41 cm) of space betw een pedicure
spa and w all w ith standard actuator

Massage motor:

12V AC, Adapter included (alternate voltages available)

Power source:

110V:

110V AC, 2.75 Amp, 60 Hz (GFCI Protected)

220V:

220V AC, 2.75 Amp, 50/60 Hz (GFCI Pr otected)

Caution: Pedicure spa must be installed by a licensed electrician and a licensed plumber,

conforming to all local and national electrical codes.

Construction:

Metal Frame w ith Acrylic Fiberglass Shells, self-contained, pre-plumbed

Crystal Clean

™

Pipe-Free

water massage system (Pipe-Free

pedicure spas): Six 'underfoot' footplate

water massage grooves, no closed loop circulating pipes, 100% fully drained,

and cleanable

Electrical sw itches:

On/Off sw itch for w hirlpool pump. A single hand-held, low voltage remote control

for massage motors, heat and seat/back position. Hot and Cold w ater supply
lines required.

Compliances:

Complies w ith ASME/ANSI Whirlpool Bathtub Specs ASME/A NSI A112.19 7M-
1995 and A112.19.8M-1995. Backflow Protection Devices for Faucets with Side
Spray: Check valves comply w ith ANSI/ASME A112.18.3M, A112.18.1M, CSA

B125, and TÜV certified.

Electrostatic Limits:

This unit may loose one ore more functions when electrostatic contact discharge
in excess of 4KV gets into accessible conductive part of the unit and can be
restored by resetting the unit.

This unit may loose one ore more functions when power surge in excess of 2KV
is applied to the AC input pow er port and can be restored by resetting the unit.
This unit may loose one ore more functions w hen subjected to fast transient

voltages in excess of 0.5KV at 5 KHz repetition frequency and can not be
restored.

Limited w arranty:

One (1) year from date of shipment.

Due to our policy of continuous improvements, all specifications are subject to change without notice.

*Note: All dimensions and weights are approximate