Manuels d'utilisation pour Whirlpool mede300

Whirlpool

Codes de produits

mede500Montre plus

, mede900, wed9400sz, wed9450, wed9470w, wed94hex, wed9550, wed95hex, wed9750

Manuel D’Utilisation (English)Manuel D’Utilisation (Français, English)

Manuel D’Utilisation

Table des matières

ELECTRIC Dryer Installation Instructions U.S.A. ONLY
1
- Para una versión de estas instrucciones en español, visite www.Whirlpool.com
  1
- Table of Contents
  1
- Dryer Safety
  1
- INSTALLATION REQUIREMENTS
  2
Tools and Parts
2
- Flat-blade screwdriver
  2
- #2 Phillips screwdriver
  2
- Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench (for adjusting dryer feet)
  2
- Level
  2
- Wire stripper (direct wire installations)
  2
- Vent clamps
  2
- Caulking gun and compound (for installing new exhaust vent)
  2
- Tin snips (new vent installations)
  2
- ¼" nut driver (recommended)
  2
- Tape measure
  2
- Pliers
  2
- Parts supplied
  2
- Parts needed
  2
Optional Equipment
3
Location Requirements
3
- You will need
  3
- Installation clearances
  3
  - Steam (Electric or Gas)
    3
  - Non-Steam (Electric or Gas)
    3
  - A
    3
  - B
    3
  - C
    3
  - D
    3
    - Back View
      3
  - Steam (Electric or Gas)
    3
  - Non-Steam (Electric or Gas)
    3
  - A*
    3
  - B
    3
  - C
    3
    - * Dimension A is approximate, depending on when the diamond marking on the leveling foot is no longer visible.
      3
    - Side View
      4
  - Steam (Electric or Gas)
    4
  - Non-Steam (Electric or Gas)
    4
  - A*
    4
  - B
    4
  - C
    4
- Installation spacing for recessed area or closet installation
  4
- Recommended installation spacing for cabinet installation
  5
  - For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required.
    5
  - Steam (Electric or Gas)
    5
  - Non-Steam (Electric or Gas)
    5
  - A*
    5
  - B*
    5
  - C*
    5
  - D**
    5
  - E
    5
  - F*
    5
  - G
    5
  - H
    5
  - I
    5
- Recommended installation spacing for recessed or closet installation, with stacked washer and dryer
  5
Electrical Requirements
5
- It is your responsibility
  5
  - To contact a qualified electrical installer.
    5
  - To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70- latest edition and all local codes and ordinances.
    5
The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.
5
A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.
5
- To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line....
  6
- Do not use an extension cord.
  6
- If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
  6
- This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical s...
  6
- If local codes do not permit the connection of a neutral ground wire to the neutral wire, see “Optional 3-wire connection” section.
  6
- A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile ...
  6
- If using a power supply cord:
  6
  - A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.
    6
  - A UL listed strain relief.
    6
- If your outlet looks like this:
  6
- If your outlet looks like this:
  6
- If connecting by direct wire:
  6
  - Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.
    6
  - 10-gauge solid copper wire (do not use aluminum) at least 5 ft (1.52 m) long.
    6
- Electrical Connection
  6
Style 1: Power supply cord strain relief
7
- Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold...
  7
- Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further t...
  7
Style 2: Direct wire strain relief
7
- Unscrew the removable conduit connector and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the ter...
  7
- Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.
  8
  - 4. Now complete installation following instructions for your type of electrical connection:
    8
4-wire (recommended)
8
3-wire (if 4-wire is not available)
8
- Electrical Connection Options
  8
- If your home has:
  8
- And you will be connecting to:
  8
- Go to Section
  8
- 4-wire connection: Power supply cord
  8
- 4-wire connection: Direct wire
  9
- 3-wire connection: Power supply cord
  10
  - Use where local codes permit connecting cabinet-ground conductor to neutral wire.
    10
- 3-wire connection: Direct wire
  10
  - Use where local codes permit connecting cabinet-ground conductor to neutral wire.
    10
- Optional 3-wire connection
  11
  - Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.
    11
- Venting Requirements
  11
  - If using an existing vent system
    11
  - If this is a new vent system
    11
    - Use a heavy metal vent. Do not use plastic or metal foil vent.
      11
    - 4" (102 mm) heavy metal exhaust vent and clamps must be used.
      11
Vent products can be purchased from your dealer or by calling Whirlpool Service. For more information, see the “Assistance or Service” section.
11
- Rigid metal vent
  11
  - For best drying performance, rigid metal vents are recommended.
    11
  - Rigid metal vent is recommended to avoid crushing and kinking.
    11
- Flexible metal vent
  12
- Elbows
  12
45° elbows provide better airflow than 90° elbows.
12
- Good Better
  12
- Clamps
  12
  - Use clamps to seal all joints.
    12
  - Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct and catch lint. Do not use duct tape.
    12
- Exhaust
  12
A and B: Recommended hood styles. C: Acceptable hood style.
12
- An exhaust hood should cap the vent to keep rodents and insects from entering the home.
  12
- Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, or bushes, snow line, etc.).
  12
- Do not use an exhaust hood with a magnetic latch.
  12
- Plan Vent System
  12
  - Choose your exhaust installation type
    12
    - Optional exhaust installations
      12
    - Alternate installations for close clearances
      13
      - Over-the-Top Installation:
        13
Part Number 4396028
13
- Periscope Installation (For use with dryer vent to wall vent mismatch):
  13
Part Number 4396037 - 0" (0 mm) to 18" (457 mm) mismatch
13
Part Number 4396011 - 18" (457 mm) to 29" (737 mm) mismatch
13
Part Number 4396014 - 29" (737 mm) to 50" (1.27 m) mismatch
13
- Special provisions for mobile home installations
  13
- Determine vent path
  13
- Determine vent length and elbows needed for best drying performance
  13
  - Use the following vent system chart to determine type of vent material and hood combinations acceptable to use.
    13
NOTE: Do not use vent runs longer than those specified in the Vent system chart.
13
Exhaust systems longer than those specified will:
13
- Shorten the life of the dryer.
  13
- Reduce performance, resulting in longer drying times and increased energy usage.
  13
- Vent system chart
  13
  - Number 90º elbows
    13
  - Type of vent
    13
  - Box /louvered hoods
    13
  - Angled hoods
    13
  - 0
    13
  - Rigid metal
    13
    - 64 ft (20 m)
      13
    - 58 ft (17.7 m)
      13
  - 1
    13
  - Rigid metal
    13
    - 54 ft (16.5 m)
      13
    - 48 ft (14.6 m)
      13
  - 2
    13
  - Rigid metal
    13
  - 3
    13
  - Rigid metal
    13
  - 4
    13
  - Rigid metal
    13
- Install Vent System
  13
NOTE: If “Y” connector can be attached directly to cold water faucet, go to Step 6. If “Y” connector cannot be attached directly to the cold water faucet, the short hose must be used. Continue with Step 3.
14
- 3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on faucet.
  14
- 4. Using pliers, tighten the couplings with an additional two-thirds turn.
  14
NOTE: Do not overtighten. Damage to the coupling can result.
14
- 5. Attach “Y” connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.
  14
- 6. One end of the long hose has a wire mesh strainer inside the coupling. Attach this end to the “Y” connector.
  14
- 7. Attach washer cold inlet hose to other end of “Y” connector. Screw on coupling by hand until it is seated on connector.
  14
- A. Inlet to cold water
  14
  - 8. Using pliers, tighten the couplings an additional two-thirds turn.
    14
NOTE: Do not overtighten. Damage to the coupling can result.
14
- 9. Attach other end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector.
  14
- 10. Using pliers, tighten the coupling an additional two-thirds turn.
  14
NOTE: Do not overtighten. Damage to the coupling can result.
14
- 11. Check that the water faucets are on.
  14
- 12. Check for leaks around “Y” connector, faucet, and hoses.
  14
- Level Dryer
  15
- Complete Installation
  15
- Steam Models Only:
  15
- All Models:
  15
  - 13. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting.
    15
If the dryer will not start, check the following:
15
- 14. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door.
  15
- There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.
  15
  - troubleshooting
    15
  - First try the solutions suggested here and possibly avoid the cost of a service call...
    15
- Dryer Operation
  15
Try the following: Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit breaker.
16
Confirm the power cord is properly installed. Refer to “Electrical Connection” for details.
16
Select a Timed Dry heated cycle, and restart the dryer.
16
If the message persists, consult a qualified electrician.
16
- “AF” (low airflow condition): The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display and return to the estimated time remaining.
  16
Try the following:
16
- Clean lint screen.
  16
- Check to see if the vent run from the dryer to the wall is crushed or kinked.
  16
- Confirm the vent run from the dryer to the wall is free of lint and debris.
  16
- Confirm the exterior vent exhaust hood is free of lint and debris.
  16
- Confirm your vent system falls within the recommended run length and number of elbows for the type of vent you are using. Refer to “Plan Vent System” for details.
  16
- Select a Timed Dry heated cycle, and restart the dryer.
  16
If the message persists, have your entire home venting run cleaned.
16
- “E” Variable (E1, E2, E3) service codes: Call for service.
  16
- Dryer Results
  16
  - Clothes are not drying satisfactorily, drying times are too long, or load is too hot
    16

Manuel D’Utilisation

Taille:

4,2 Mo
Pages:

16
Language:

English

Ouvrir le manuel

Manuel D’Utilisation

Table des matières

Manuel D’Utilisation

Taille:

3,6 Mo
Pages:

28
Languages:

Français, English

Ouvrir le manuel