Fortin Auto Radio Inc. ANT900 Manuale Utente
ACCESSORY PRESET
Heater & Heated Seat(s): When leaving the vehicle it is recommended that the driver pre-set
the climate controls in preparation for a later Remote-Start. When the vehicle Remote-
Starts, the current (or last) setting for the climate controls, windshield wipers (and other
accessories) will be used. When setting the blower motor (fan speed) and heated seats (if
equipped) should not be left on HIGH. It is recommended to leave these settings on either
a LOW or MEDIUM setting.
the climate controls in preparation for a later Remote-Start. When the vehicle Remote-
Starts, the current (or last) setting for the climate controls, windshield wipers (and other
accessories) will be used. When setting the blower motor (fan speed) and heated seats (if
equipped) should not be left on HIGH. It is recommended to leave these settings on either
a LOW or MEDIUM setting.
Windshield Wipers & Radio & Headlights: Some vehicles require the radio, windshield wiper,
headlight circuits to become energized while running under Remote-Start. When leaving the
vehicle you must ensure that the windshield wiper and headlight switches are turned off.
Leaving the headlights on with some vehicles could cause them to remain on even after the
Remote-Starter has shut down, resulting in a dead battery.
headlight circuits to become energized while running under Remote-Start. When leaving the
vehicle you must ensure that the windshield wiper and headlight switches are turned off.
Leaving the headlights on with some vehicles could cause them to remain on even after the
Remote-Starter has shut down, resulting in a dead battery.
Rear Defrost: On most vehicles the Rear Defrost can only be activated after the vehicle
has been started and in most cases this feature is not included with a Remote-Starter
installation. On some vehicles it may be possible for the installer to hook this feature up
so it either automatically enables after Remote-Start or can be enabled by using an AUX
output. (See Auxiliary Outputs page 11)
has been started and in most cases this feature is not included with a Remote-Starter
installation. On some vehicles it may be possible for the installer to hook this feature up
so it either automatically enables after Remote-Start or can be enabled by using an AUX
output. (See Auxiliary Outputs page 11)
Driver Presets: Some vehicles retain different seat, mirror and radio settings for each
driver. Different driver presets are not controlled by the Remote-Starter, however they may
be controlled with the Bypass/Interface Kit.
driver. Different driver presets are not controlled by the Remote-Starter, however they may
be controlled with the Bypass/Interface Kit.
READY MODE (MANUAL TRANSMISSION ONLY)
Two activation methods are possible, please consult the salesman or installer to determine which of
these modes applies to your vehicle.
There are always safety concerns for a manual transmission vehicle to accidentally start while in gear,
Ready Mode alleviates these concerns. The driver must enable Ready Mode in order to Remote-Start the
vehicle at a later time. Once Ready Mode is set-up the vehicle can be started/stopped at will, as many
times as needed. However once the parking brake is disengaged, the hood is opened, or any of the doors
are opened, Ready Mode will deactivate and the vehicle will not start until Ready Mode is reactivated.
these modes applies to your vehicle.
There are always safety concerns for a manual transmission vehicle to accidentally start while in gear,
Ready Mode alleviates these concerns. The driver must enable Ready Mode in order to Remote-Start the
vehicle at a later time. Once Ready Mode is set-up the vehicle can be started/stopped at will, as many
times as needed. However once the parking brake is disengaged, the hood is opened, or any of the doors
are opened, Ready Mode will deactivate and the vehicle will not start until Ready Mode is reactivated.
METHOD 1
PROGRAMMED BY DEFAULT THIS METHOD WILL ACTIVATE THE REMOTE CAR STARTER SEQUENCE ONLY WHEN
THE END USER IS USING THE REMOTE CAR STARTER REMOTE:
PROGRAMMED BY DEFAULT THIS METHOD WILL ACTIVATE THE REMOTE CAR STARTER SEQUENCE ONLY WHEN
THE END USER IS USING THE REMOTE CAR STARTER REMOTE:
The vehicle must be running.
STEP 1
and
Make sure that all doors are closed and the transmission is in the
NEUTRAL position.
NEUTRAL position.
STEP 2
Engage the parking brake.
STEP 3
Release the brake pedal.
STEP 4
Press the START button for 3 seconds. The remote Green Led
fl ash and a ascending melodie will sound to confi rm. The park-
ing lights will fl ash once and then remain on.
fl ash and a ascending melodie will sound to confi rm. The park-
ing lights will fl ash once and then remain on.
STEP 5
OFF
Remove the key from the ignition barrel.
The vehicle will remain running with the Remote-Starter.
The vehicle will remain running with the Remote-Starter.
STEP 6
Exit the vehicle and close all of the doors.
The Remote-Starter will stop running once all the doors are
closed.
The Remote-Starter will stop running once all the doors are
closed.
Page 6 / 15