Omnitron iConverter XGT+ 8589N-1-D Manuale Utente
Codici prodotto
8589N-1-D
application examples
Data Center Application
In this application, new 10GBASE-T servers are added to an
In this application, new 10GBASE-T servers are added to an
existing rack of servers with SFP+ interfaces. The servers
are connected to a Top of Rack fiber switch with Direct
Attach Copper (DAC) cables. The switch is connected to an
aggregation switch in the data center with multimode fiber.
New 10GBASE-T servers have been added to the rack.
New 10GBASE-T servers have been added to the rack.
10GBASE-T servers are used due to their low cost. They have
LAN on Motherboard (LoM) technology, so the 10GBASE-T
RJ-45 ports are integrated into the server.
iConverter XGT+ plug-in media converters are installed in a
iConverter XGT+ plug-in media converters are installed in a
high density (2U high), iConverter 19-Module chassis with
redundant power supplies. CAT-6A patch cords connect the
new servers to the XGT+ media converters, and DAC cables
connect the media converters to the fiber switch.
Since the 10GBASE-T servers are connected to the
Since the 10GBASE-T servers are connected to the
10GBASE-T media converters over a short cable (less than
30 meters) they can take advantage of the 10GBASE-T
Short Reach mode, in which all devices operate with a lower
CWDM Data Center Interconnect Application
This application shows two data centers interconnected by four
This application shows two data centers interconnected by four
10G Ethernet connections across a CWDM common fiber link
(multi-color line) where fiber availability is limited and CWDM
multiplexers are used to increase the fiber capacity.
An iConverter 4-Channel CWDM/X multiplexer module and four
An iConverter 4-Channel CWDM/X multiplexer module and four
iConverter XGT+ plug-in modules are installed in an iConverter
5-Module Chassis at both locations. The iConverter XGT+
modules are used to convert the RJ-45 interfaces on the 10G
Ethernet switch ports to CWDM wavelengths required by the
CWDM/X multiplexers.
The SFP+ port of each iConverter XGT+ contains an SFP+
The SFP+ port of each iConverter XGT+ contains an SFP+
CWDM transceiver that generates a specific CWDM optical
wavelength, and is connected to the CWDM/X multiplexer
with fiber patch cables (where each colored line represents a
different wavelength).
MUX
Fiber Links to Aggregation Switches
Existing Top
of Rack Switch
iConverter XGT+
Media Converters
in 19-Module Chassis
New 10G
Servers
Existing SFP+
Servers
{
{
DAC
CAT-6A
MM Fiber
Page 2
Data Center
Data Center
CAT-6A Cables
Fiber Patch Cables
10G Blade Switch
10G Blade Switch
CWDM Mux and (4) XGT+ Modules in 5-Module Chassis
MUX
MUX
manaGement
Management of the plug-in module is accomplished by
installing a Network Management Module (NMM2) or a media
converter with integrated management (such as an iConverter
10/100M2) that provides monitoring, remote configuration and
trap notification.
MSA compliant pluggable transceivers support digital
MSA compliant pluggable transceivers support digital
diagnostic capabilities, providing real time optical diagnostic
information including fiber optic TX and RX power, voltage
and transceiver temperature conditions on the plug-in module.
These parameters can be monitored by the installed Network
Management module.
Utilizing management, the programmable DWDM tunable
Utilizing management, the programmable DWDM tunable
transceivers can be configured and saved through convenient
menu selections.
Plug-in modules feature full management capabilities, including
Plug-in modules feature full management capabilities, including
remote configuration, status reporting, fault/alarm detection,
loopback functionality, link status and transceiver threshold
alerts.
transmit power. Short reach mode is specified in the IEEE
10GBASE-T standard, and conserves energy and produces
less heat.
iConverter
XGT+