High End Systems High End LCD Controller for Studio Color Manuale Utente
Studio Color LCD Controller
Other Connectors
2-23
2
Other Connectors
This section describes how to connect cabling to the other
connectors on the controller’s rear panel. Because these
other connectors are used in conjunction with advanced
functions described further in Chapters 6 and 7, only a brief
explanation is found here.
connectors on the controller’s rear panel. Because these
other connectors are used in conjunction with advanced
functions described further in Chapters 6 and 7, only a brief
explanation is found here.
Figure 2-17. Locations of the other connectors on
the controller’s rear panel.
the controller’s rear panel.
Serial communication port: Connect the male end of a
standard 9-pin RS-232C serial communication cable to this
port for playback control using Lightwave Control Center
(LCC) software, or for backing up/restoring memories, pages
and presets using a personal computer. The port operates at
9600 baud, 8 data bits, no parity, and 1 stop bit. For more
details about using this port with LCC, see the section titled
“Lightwave Control Center” on page 6-31. For more
information about backup/restore, see Chapter 7.
standard 9-pin RS-232C serial communication cable to this
port for playback control using Lightwave Control Center
(LCC) software, or for backing up/restoring memories, pages
and presets using a personal computer. The port operates at
9600 baud, 8 data bits, no parity, and 1 stop bit. For more
details about using this port with LCC, see the section titled
“Lightwave Control Center” on page 6-31. For more
information about backup/restore, see Chapter 7.
Analog Inputs ports: Two locking 8-pin DIN connectors
that enable the remote recall of pages or presets using an
analog controller. The first connector is for analog channels
1 through 6; the second connector is for analog channels 7
through 12. For more details about the usage of this port, see
the section titled “Analog Inputs Ports” on page 6-15.
that enable the remote recall of pages or presets using an
analog controller. The first connector is for analog channels
1 through 6; the second connector is for analog channels 7
through 12. For more details about the usage of this port, see
the section titled “Analog Inputs Ports” on page 6-15.
DATA LINK
OUT
CAUTION
WARNING
PERSONALITY
SLAVE
MASTER
RS-232
SERIAL PORT
1-6
ANALOG INPUTS
7-12
REMOTE
ENABLE
FUSE
CAUTION
voltage
select
1 2 3 4
A
B
M IDI
IN
OUT
STEREO
AUDIO
INPUT
INPUT
115
To reduce t he risk of f ire or
electr ic shock, do not expose
t his device t o rain or mois ture.
electr ic shock, do not expose
t his device t o rain or mois ture.
L
R
R
IMPORTANT SAFETY INFORMATION. SEE INSTRUCTION MANUAL BEFORE USE.
WICHTIGE SICHERHEITSINFORMATIONEN. BEDIENUNGSANLEITUNG VOR GEBRAUCH LESEN!
D'IMPORTANTE CONSIGNE DE SÉCURITÉ. VOYEZ LE MANUEL D'INSTRUCTION AVANT L'UTILISATION DE L'APPAREIL.
WICHTIGE SICHERHEITSINFORMATIONEN. BEDIENUNGSANLEITUNG VOR GEBRAUCH LESEN!
D'IMPORTANTE CONSIGNE DE SÉCURITÉ. VOYEZ LE MANUEL D'INSTRUCTION AVANT L'UTILISATION DE L'APPAREIL.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause har mful interferences,
and (2) this device must accept any interference
that may cause undesired operation.
Operation is subject to the following two conditions:
(1) This device may not cause har mful interferences,
and (2) this device must accept any interference
that may cause undesired operation.
To prevent electric shock, do
not remove cover. No user
serviceable parts inside.Refer
servicing to qualified service
personnel. Replace fuse with
same type and rating.
not remove cover. No user
serviceable parts inside.Refer
servicing to qualified service
personnel. Replace fuse with
same type and rating.
RA T I NG I N FO R MA TI O N
V O L TA G E : 1 1 5 V A C/ 2 3 0V A C
CU RR E NT: 0 . 2 5A / 0 . 1 5 A
FR E Q UE NC Y : 5 0 -6 0 HZ
V O L TA G E : 1 1 5 V A C/ 2 3 0V A C
CU RR E NT: 0 . 2 5A / 0 . 1 5 A
FR E Q UE NC Y : 5 0 -6 0 HZ
115 V 0.5 A, SLOW BLOW
230 V 0.315 A, SLOW BLOW
230 V 0.315 A, SLOW BLOW
1 2 3 4
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Serial communcation
port
Analog Inputs
ports
Remote Enable
port
Stereo Audio Input
port
MODEL
SERIAL
DATE
QC
VOLTAGE
HZ
230
15FM123456
Cyberlight LCD Controller
50
805
90001
ETL Listed
Conforms to
UL Std. 1950
UL Std. 1950
Certified to
CAN/CSA C22.2 No. 950
67501
R
C
R
LIGHTWAVE RESEARCH
2217 West Braker Lane
Austin, Texas U.S.A.
2217 West Braker Lane
Austin, Texas U.S.A.