Viking VDD5450SS Utilizzo E Cura
3
PLANNING
ELECTRICAL SPECIFICATIONS
Model VDVI600 - Internal Flex:
120 VAC • 60 Hz • 3.0 A
Models VDVE900, VDVE1200 - Exterior
120 VAC • 60 Hz • 6.0 A (max.)
Model VDVI600 - Internal Flex:
120 VAC • 60 Hz • 3.0 A
Models VDVE900, VDVE1200 - Exterior
120 VAC • 60 Hz • 6.0 A (max.)
TAKE MEASUREMENTS
Due to its fl exible design, this downdraft system can be used to ex-
haust airborne contaminants when cooking with a variety of gas or
electric cooking appliances - including cooktops, rangetops, slide-in
ranges and free-standing ranges.
It can be mounted in island, peninsula, or conventional wall loca-
tion. The blower (purchase separately) and electrical panel can be
mounted to the downdraft unit, inside the cabinet, or in a convenient
remote location.
This unit can be easily installed following these basic steps:
• Cut out the countertop opening.
• Mount the unit in the cabinet.
• Install the blower and electrical panel.
• Connect the ductwork and electrical.
• Mount the trim/door.
• Install the cooking appliance.
Note: the high level of air fl ow of this appliance may effect the gas
fl ame on some types of gas cooktops. This is NORMAL and will cause
no harm, but can be corrected by lowering the speed of the blower.
haust airborne contaminants when cooking with a variety of gas or
electric cooking appliances - including cooktops, rangetops, slide-in
ranges and free-standing ranges.
It can be mounted in island, peninsula, or conventional wall loca-
tion. The blower (purchase separately) and electrical panel can be
mounted to the downdraft unit, inside the cabinet, or in a convenient
remote location.
This unit can be easily installed following these basic steps:
• Cut out the countertop opening.
• Mount the unit in the cabinet.
• Install the blower and electrical panel.
• Connect the ductwork and electrical.
• Mount the trim/door.
• Install the cooking appliance.
Note: the high level of air fl ow of this appliance may effect the gas
fl ame on some types of gas cooktops. This is NORMAL and will cause
no harm, but can be corrected by lowering the speed of the blower.
PLAN THE DUCTWORK
1. Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. However,
it is recommended that oversized cabinets be used for easier
installation.
it is recommended that oversized cabinets be used for easier
installation.
2. Cooktop depth can vary greatly from one to another. This may
cause the fi t of these two appliances to be rather tight.
Pay special attention to the areas of potential interference highlighted
below. A countertop with (A) a raised lip and/or (B) a backsplash may
not allow enough fl at countertop for a proper installation. Note that
2-3/4" of fl at countertop is required behind cooktop and that 1-3/4"
is necessary between the back edge of the cooktop and the inside
of cabinet back.
below. A countertop with (A) a raised lip and/or (B) a backsplash may
not allow enough fl at countertop for a proper installation. Note that
2-3/4" of fl at countertop is required behind cooktop and that 1-3/4"
is necessary between the back edge of the cooktop and the inside
of cabinet back.
A
B
C
D
E
F
HOUSING
1. The downdraft blower system is designed for use with
8" round ductwork using a fl ex blower or 10" Round
ductwork using a remote blower. (Purchase blowers
separately.) Six (6) different discharge connections are
available - with side-to-side adjustment for accurate
alignment of ductwork:
A = 8" Round, Left Discharge out of Flex Blower
B = 8" Round, Right Discharge out of Flex Blower
C = 8" Round, Down Discharge out of Flex Blower
(Electrical Box to be mounted remotely)
D = 2" x 19¼", Left Discharge out of Housing
to Remote Blower or Flex Blower in remote
location. Use 2" x 19¼" to 8" round transition,
2" x 19¼" to 10" round transition, or 2" x 19¼"
ductwork as appropriate.
E = 2" x 19¼", Right Discharge out of Housing
to Remote Blower or Flex Blower in remote
location. Use 2" x 19¼" to 8" round transition,
2" x 19¼" to 10" round transition, or 2" x 19¼"
ductwork as appropriate.
F = 2" x 19¼", Rear Discharge out of Housing
to Remote Blower or Flex Blower in remote
location. Use 2" x 19¼" to 8" round transition,
2" x 19¼" to 10" round transition, or 2" x 19¼"
ductwork as appropriate.
2. For best performance: Choose the ducting option which
allows the shortest length of ductwork and a minimum
number of elbows and transitions. Check location of
fl oor joists, wall studs, electrical wiring or plumbing for
possible interference.
CONTENTS
These parts are included with your downdraft housing:
1 - Parts Bag
1 - Trim Kit
4 - Support Legs
1 - Electrical Panel
2 - Support Brackets
1 - Parts Bag
1 - Trim Kit
4 - Support Legs
1 - Electrical Panel
2 - Support Brackets
2-3/4"
2-1/2"
FLEX
BLOWER
*
*
Remote blowers use 8" or 10" round remote discharge
plate instead of fl ex blower.