Manuali utente per Lucent Technologies 555-230-128

Sommario

• Table of Contents

  3
• About This Book

  7
  • Conventions Used in This Book

    7
• 1. Install and Cable the Cabinets

  9
  • Check Customer’s Order

    9
  • Correcting Shipping Errors

    9
  • Unpack and Inspect

    9
  • Comcodes for CMC

    11
  • Install the System Cabinets

    14
    • Set the Carrier Address ID — All Cabinets

      14
    • Floor-Mount the Cabinet

      15
    • Wall-Mount the Cabinets

      16
      • Install Plywood Backing onto Wall

        16
    • Install Cabinet A — Wall-Mount

      17
      • Install 2 or 3 Vertically Mounted Cabinets

        19
      • Install 2 Cabinets Vertically and 1 Cabinet Horizontally

        20
    • Install Left and Right Panels — Wall-Mount

      21
  • AC Power and Ground

    22
    • AC Power and Ground

      22
      • Check AC Power

        22
      • Approved Grounds

        23
    • Uninterruptible Power Supply

      24
    • CMC Cabinet Power Switch

      25
    • Connect Cabinet Grounds and Other Grounds

      25
      • Install the Ground Block

        27
    • Install Coupled Bonding Conductor

      29
    • Connect and Route Cabinet AC Power Cords

      29
  • Cable the System

    31
    • Install Processor Interface Cable — Cabinet A Only and TDM/LAN Bus Terminator

      31
    • Cable the Multi-Cabinet System — Wall-Mount

      32
      • Vertically Mounted System

        32
      • Vertically and Horizontally Mounted System

        33
  • Install Main Distribution Frame and External Modem

    34
    • Install Main Distribution Frame and External Modem

      34
      • Install the MDF

        34
      • Install the External Modem

        34
    • Cable the MDF and Modem

      35
      • Bottom-mounted MDF

        35
      • Top-Mounted MDF

        36
  • Install Equipment Room Hardware

    37
    • Cross-Connect the Cabinets to the MDF

      37
    • Allowable Circuit Packs for CMC

      37
    • Circuit Pack Installation

      41
      • Circuit Pack Slot Loading

        42
    • Install Sneak Fuse Panels

      46
    • Label the Main Distribution Frame

      49
  • Install and Set Up the Management Terminal

    50
    • Set Up the Management Terminal

      51
    • Remotely Connect Terminal

      52
  • Set Ringing Option

    53
  • Activate and Administer the System

    54
    • Power Up System

      54
      • Single Cabinet Installations

        54
      • Multi-Cabinet Installations

        54
    • System Administration

      54
      • Log into the System

        55
      • Check System Status

        55
      • Change Customer Options

        55
      • Set Country Options

        56
      • Change Craft Password

        58
      • Set Date and Time

        59
      • Circuit Pack Administration

        61
      • Set System Maintenance Parameters

        61
      • Administer the Attendant Console

        62
      • Save Translations

        62
      • Add Translations

        62
  • Install and Wire Telephones and Other Equipment

    63
    • Install and Wire Telephones and Other Equipment

      63
      • Telephone Connection Examples

        63
      • Connect Adjunct Power

        65
      • Analog Station or 2-Wire Digital Station Example

        66
      • Analog Tie Trunk Example

        67
      • Digital Tie Trunk Example

        68
      • DS1 Tie Trunk Example

        69
      • Collocated DS1 Tie Trunks

        69
      • 3-Pair and 4-Pair Modularity

        71
      • Adjunct Power Connections

        72
      • Auxiliary Power

        73
    • Install Attendant Console — Optional

      74
      • Hard-Wire Bridging

        74
      • Dual Wiring of 2-Wire and 4-Wire Endpoints

        74
    • Install 26B1 Selector Console — Optional

      74
  • Connect External Alarms and Auxiliary Connections

    75
    • Alarm Input

      75
    • Alarm Output

      75
    • Emergency Transfer and Auxiliary Power

      76
  • Telephone Pin Designations

    76
  • CAMA/E911 Installation

    77
    • Configuration

      77
    • Hardware Setup

      77
    • Administration Setup

      77
  • Install the BRI Terminating Resistor

    85
    • Terminating Resistor Adapter

      86
    • Closet Mounted (110RA1-12)

      87
  • Install Multi-point Adapters

    89
    • BR851-B Adapter (T-Adapter)

      89
    • 367A Adapter

      90
    • Basic Multi-point Installation Distances

      91
  • Install Off-Premises Station Wiring

    92
    • Install Off-Premises or Out-of-Building Stations

      92
    • Analog Off-Premises Stations

      92
    • Circuit Protectors

      95
    • Digital Out-of-Building Telephones

      96
  • Install Emergency Transfer Unit and Associated Telephones

    97
    • Install the Emergency Transfer Panel

      97
      • Install Telephone for Power Transfer Unit

        104
  • Connect Modem to Telephone Network

    105
    • External Modem Option Settings

      106
• 2. Installation Completion and Cable Pinouts

  109
  • Perform System Administration

    109
    • Resolve Alarms

      109
    • Enable Alarm Origination to INADS

      110
    • Place a Test Call

      110
  • Set Neon Voltage — Ring Ping

    111
  • Installation Completion

    112
  • Power Supply LED Indications

    112
  • TN760D Tie Trunk Option Settings

    113
  • TN464E/F Option Settings

    115
  • Connector and Cable Diagrams — Pinout Charts

    117
    • Processor Interface Cable Pinout

      119
• A. References

  129
  • Related Documents

    129
  • How to Order Documentation

    130
  • How to Comment on This Book

    130
  • Where to Call for Technical Support

    130
  • Security Issues

    130
  • Trademarks

    131
  • Standards Compliance

    132
  • Electromagnetic Compatibility Standards

    133
    • European Union Standards

      134
  • Federal Communications Commission Statement

    135
    • Part 68: Statement

      135
      • Means of Connection

        136
• Index

  137