Marantz AV9000 ユーザーズマニュアル

7

This chapter describes the functions which need to control the
AV9000.  See page 27 and following pages to refer other function of
the RC-18SR.

v

These two buttons are use for turning on or off AV9000.

m

The DIRECT command buttons (4 on each side of the LCD display, 8
total) work with the PAGE buttons (4 pages for each source
component) to provide up to 32 dedicated specialized functions for
each of the 11 function input selectors. Each DIRECT function may
also be provided with an alphanumeric function indicator visible in
the LCD display.  Press the 

or 

button . to control the

receiver.

Press one of these buttons to select a surround mode for the current
listening session.

MODE1 1 

Auto select surround modes

2 

Dolby Digital or Pro Logic decoding

3 

THX cinema decoding

4 

DTS-cinema or DTS-music

5 

Hall surround sound

6 

Matrix surround sound

7 

Movie surround sound

8 

Stereo sound (no surround)

MODE2 1 

analog / digital select switch
Switches between the analog input and the
digital input.

2 

source direct switch
When this switch is pressed, the signals are
transmitted by bypassing the tone control
circuitry so that they can be reproduced with
higher quality.

3 

attenuate for analog input

4 

on screen display
Once the button is pressed, the on-screen
display is turned on and each a control button
related to the AV9000 is pressed thereafter, the
information will be displayed on the TV screen.
When the button is pressed again to turn the
on-screen display off, it disappears from the TV
s c r e e n .   ( R e f e r   t o   “ O N - S C R E E N   M E N U
SYSTEM” on page 10)

5 

monaural decoding
When this button is pressed, the monaural
sound is selected.

6 

3-D surround decoding
This button is not used for AV9000.

7 

NIGHT mode for Dolby Digital
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice. This
function reduces the voice by 1/3 to 1/4 at
maximum.  Thus, it eliminates the occurrence
of an abruptly loud voice at night. However, the
function is valid only for the case when the
Dolby Digital signal (AC-3) is entered into
digital Input and data to compress the voice
exists in the signal to be played back.

8 

activates multi-room mode

MODE3 1 

increases treble

2 

decreases treble

3 

increases bass

4 

decreases bass
The button 1 to 4 are used to control the tone.

5 

activates RE-EQ function
This button is not used for AV9000.

6 

channel select button
Press this button to adjust the volume levels of
t h e   f r o n t ,   c e n t e r ,   s u r r o u n d ,   s u b w o o f e r
channels. Each press of the button changes
the channel which can be adjusted.

@0

This indicator is for 96 kHz PCM digital input signal.  If the selected
digital input signal is 96 kHz PCM audio, this indicator will illuminate.

@1

These indicators display the currently selected DTS mode.  If you
select DTS cinema or DTS music by 

buttons u, these indicators will display.

@2

These indicators show which channels are encoded with a digital
input signal.
If the selected digital input signal is Dolby Digital 5.1ch or DTS 5.1ch,
“L”, “C”, “R”, “LS”, “RS” and “LFE” will light up.
If the digital input signal is 2 channel PCM-audio, “L” and “R” will be
displayed.

These indicators are depend on the digital input, without reference
to the surround mode.

@3

This indicator is a monitor for analog audio input signal.  If the
selected analog audio input signal is greater than the capable level of
internal processing, this indicator will show.  If this indicator is lit up,
you should press the ATT button on the remote control.