Marantz AV9000 ユーザーズマニュアル

8

MODE3 7 

Increases channel level volume

8 

decreases channel level volume
After pressing the CH+ button, use the LVL+
and LVL- buttons to adjust the volume level of
each speaker channel.

Note: These level controls are for temporary adjustment,

so these setup is not memorized for each source.

PROCESSOR 1 

increases external decoder’s volume
This button is not used for AV9000.

2 

decreases external decoder’s volume
This button is not used for AV9000.

3 

6 channel direct button
When the surround processor is connected to
the DIRECT IN JACKS, press this button to play
it.

4 

bypasses external processor’s decoding

5 

sleep timer button
This button is used for setting the sleep timer.

6 

display off function
When this button is pressed, the display is
turned off.

7 

surround mode select button
This button is not used for AV9000

8 

phono function button
This button is not used for AV9000.

BAND

1 

FM band button

2 

AM/MW band button

3 

long wave band button
This button is not used for AV9000

4 

selects radio band button

5 

mono/stereo/muting mode selector button

6 

time display button
This button is not used for AV9000

7 

frequency or preset channel display select
button
This button is not used for AV9000

8 

preset scan button

,

These buttons are used to select any 1 of the 4 pages of 8 functions
for each 

button, as explained above.

.

These buttons are used for selecting the input function.  Press one of
these buttons twice within 2 seconds.

⁄1

These buttons are used to raise and lower the main system volume
level.

⁄2

They are useful for tuning a pre-set radio station and setting a station
name.

⁄3

This button is used to enter the tuner preset memory numbers and
station names.

⁄4

This button is used to cancel certain memory or programming
operations.

⁄6

The cursor buttons can be used to navigate within on-screen menus.
These buttons are unavailable when the mode is set to DSS, TV or
DVD.

⁄7

This button can be used to mute the sound temporarily.

⁄9

This button is used to activate the back-lit LCD screen and back-lit
keys.

Press 

button ..  Press 

D2 on page2 to make higher quality

Hi-Fi sounds.  When this function is selected, the signals are
transmitted by bypassing the tone control circuitry so that they can be
reproduced with higher quality.

The surround mode is switched automatically to STEREO when
the source direct function is turned on.
The source direct function is available with a digital source when
the input signal is the PCM.
If a Dolby Digital signal or DTS signal input to AV9000, in this
mode output from AV9000 will be muted.

Press 

button ..  Press 

D3 on page2 to attenuate the

analog AUDIO signal selected with the 

buttons.  When

the analog input signal is too great and the voice distorts even by
throttling the AV9000 VOLUME control, turn on the function. “ATT” is
displayed when this function is activated.
The signal-input level is reduced by about half. Attenuate is invalid for
use with the output signal of “REC OUT” (TAPE, CD-R/MD, VCR1 and
DSS/VCR2 output).
This function is memorized for each input function.

Press 

button ..  Press 

D8 on page2 to switch the unit to

multi room mode.  “MULTI ROOM” appears in the display.

Press 

button ..  Press 

D6 on page4, the display is turned

off and the display off indicator lights up ( DISP ).  To turn the display
ON again, perform the previous procedure.

Press 

button ..  Press 

D1 on page 1 to select the auto

stereo mode or mono mode when the FM band is selected. The AUTO
indicator lights in the auto stereo mode.

Press 

button  ..  Press 

D4 on page 1 to switch

between FM mode and AM mode of the tuner.
Tuner band is changed in the following sequence.

FM 

→ AM → FM → ...