hussman P/N IGUP-AB-0904 ユーザーズマニュアル

Rev. 0904

Electrical

WIRING COLOR CODE

C o l o r D e s c r i p t i o n

D e s c r i p c i o n

G RO U N D

T I E R R A M A S A

M A S S E

A N T I - S W E AT

A N T I C O N D E N S C I O N

A N T I - S U I N T E M E N T

L I G H T S

L U C E S

E C L A I R A G E

R E C E P TA C L E S

E N C H U F E R

R E C E P TA C L E

T- S TAT / S O L E N O I D 230 V THERMOSTATO / SOLENOID (230 VAC)

SOUPAPE A SOLENOID (230 V)

T- S TAT / S O L E N O I D 115 V THERMOSTATO / SOLENOID (115 VAC)

SOUPAPE A SOLENOID (115 V)

FAN MOTORS

VENTILADORES

VENTILATEUR

S TA N DA R D C A S E W I R E C O L O R C O D E

C O D I G O D E C O L O R E S D E L O S A L A M B R E S PA R A L A S V I T R I N A S E S TA N DA R

C O D E C O U L E U R P O U R F I L S D E B O I T I E R N O R M A L I S E

4 3 0 - 0 1 - 0 3 3 8 r 9 9 0 8

CASE MUST BE GROUNDED

NOTE: Refer to label illustrated above that is affixed to case to

determine the actual configuration as checked in the “TYPE
INSTALLED” boxes.

ELECTRICAL CIRCUIT IDENTIFICATION

Standard lighting for all models will be full length fluores-
cent lamps located within the case at the top.
The switch controlling the lights, the plug provided for
digital scale, and the thermometer are located at the rear
of the case mullion.

ELECTRICAL SERVICE RECEPTACLES
(WHEN APPLICABLE)

The receptacle that is provided on the exterior back of
these models is intended for computerized scales with a
fifteen amp maximum load, not for large motors or other
high wattage appliances. It should be wired to a dedicated
circuit.

BEFORE SERVICING

ALWAYS DISCONNECT ELECTRICAL

POWER AT THE MAIN DISCONNECT

WHEN SERVICING OR REPLACING ANY

ELECTRICAL COMPONENT.

This includes (but not limited to) Fans, Heat-

ers, Thermostats, and Lights.

FIELD WIRING & SERIAL PLATE AMPERAGE

Field Wiring must be sized for component amperes
printed on the serial plate. Actual ampere draw may be

less than specified. Field wiring from the refrigeration
control panel to the merchandisers is required for re-
frigeration thermostats. Most component amperes are
listed in the “Case Specs” section, but always check the
serial plate.

BALLAST LOCATION

Ballasts are located within the access panel that runs
the length of the rear of the case. Refer to diagram on
page 6.

WIRING & SERIAL PLATE AMPERAGE

Field Wiring must be sized for component amperes
stamped on the serial plate. Actual ampere draw may be
less than specified. Field wiring from the refrigeration con
trol panel to the merchandisers is required for refrigera-
tion thermostats. Most component amperes are listed in
the "Case Specs" section, but always check the serial plate.

ASHRAE COLOR CODE

NOTE: All other manufacturers have no standard sensor codes.

Case Control Systems

SENSOR COLOR

Manufacturer ® >

EIL

Location

Coil Inlet

Color

Blue

Part#

225-01-1755

225-01-3255

Coil Outlet

Color

Red

Part#

225-01-1757

225-01-3123

Discharge Air

Color

Green

Part#

225-01-1756

225-01-3260

Return Air

Color

Purple

Green

Part#

225-01-1758

225-01-3260

Defrost Term.

Color

White

Orange

Part#

225-01-0650

225-01-3254

Liquid Line

Color

White

Blue

Part#

225-01-0650

225-01-3255