Guangzhou Chiyuan Electronic Co. Ltd. 300L ユーザーズマニュアル

2.9 TH_CURV

TH CURV THROTTLE CURVES

This function makes the throttle high side and brake side direction servo operation

quicker or milder. It has no effect on the servo maximum operation amount. For the high

side, selection from among three kinds of curves (EXP/VTR/CUR) is also possible.

Note: When the course conditions are good and there is no sense of torque at the power

unit, set each curve to the + side (quick side). When the road surface is slippery and the

drive wheels do not grip it, set each curve to the - minus (mild) side.

Note: Brake side only has EXP curves.

1 Press “ENTER” to see FUNCTION MENU

2 Use the +/- Keys to select the TH CURV function and press ENTER.

3 Press ENTER to select a setting.

4 Use the +/- Key to change the value.

5 Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to the

Main Screen.

STEERING

M:0 %
H:100%

T H _ C U R V 1 0 . 2 V

M : E X P

4 3

R :

B R : 0

STEERING

M:0 %
H:100%

T H _ C U R V 1 0 . 2 V

Neutral

Quick forward(R:0~100)

Mild forward(R:-100~0)

STEERING

M:0 %
H:100%

T H _ C U R V 1 0 . 2 V

Neutral

Mild backward(BR:-100~0)

TH. POS

Adjustment method for EXP curve

--Select EXP at setup item “M”

--Select setup item “R” and make the following adjustments:

1.Forward side adjustment:

Use the (+) button to adjust the + side when you want to quicken the rise and use the(-)

button to adjust the - side when you want to make the rise milder.

2.Brake side adjustment:

Select the setting item "BR" by ENTER button and use the (+) button to adjust the + side

when you want to quicker the rise and use the (-) button to adjust the - side when you want

to make the rise milder.

3.When ending setting, return to the initial screen by pressing the EXIT.

M : E X P

- 3 2

R :

B R : 0

M : E X P
R : - 3 2

: - 8 0

B R

R/C Introduction Manual

This function is used to change the sensitivity of the steering servo around the neutral

position. It has no effect on the maximum servo travel.

Note: When the setting is not determined, or the characteristics of the model are

unknown, start with 0% ( when EXP is set to 0%,servo movement is linear)

1.Press “ENTER” to see FUNCTION MENU

2.Use the +/- Keys to select the ST CURV function and press ENTER.

3.Use the +/- Key to change the value.

4.Press EXIT to save and return to FUNCTION MENU, press EXIT again to return to the

Main Screen.

STEERING CURVER adjusting value range: -100%~+100% Default is 0%(Linear)

Steering EXP adjustment

1.When you want to quicken steering operation, use the (+) button to adjust the + side.

When you want to make steering operation milder, use the (-) button to adjust the - side.

2 .When ending setting, return to the function menu by pressing the (EXIT) button .

TERMS: M-MODE, R--RATE

2.7 REV

This function reverses the direction of operation of

the servos related to transmitter steering, throttle, and

channel 3 operation.

1.Press “ENTER” to see FUNCTION MENU.

2.Press “+” or “-“ to choose REVERSE, and

press “ENTER” to enter REVERSE adjusting

interface.

3.Press “ENTER” to choose each Channel.

4.Press “+” to increase and “-” to choose

“REV” or “NOR”.

R E V E R S E 1 0 . 2 V

T H A U X

S T

R E V
N O R

5.Press “EXIT”to save your setting and leave REVERSE interface, and back to the

function menu interface.

Note: However, when the position set by trim or sub trim shifts from the center, the

center becomes the opposite side.

TERMS: ST-STEERING, TH-THROTTLE,AUX-AUXILLIARY

2.8 ST_CURV

S T _ E X P 1 0 . 2 V

M :

E X P

R : 0 %

S T _ E X P 1 0 . 2 V

F u n c t i o n 1 0 . 2 V

5 : S T C U R V

6 : T H C U R V
7 : A B S
8 : M O D E L

M :

E X P

R : 5 0 %