PAR Technologies PARASTATION5 V5 ユーザーズマニュアル
ParaStation5 Administrator's Guide
13
Chapter 4. Configuration
After installing the ParaStation software successfully, only few modifications to the configuration file
parastation.conf(5) have to be made in order to enable ParaStation on the local cluster.
parastation.conf(5) have to be made in order to enable ParaStation on the local cluster.
4.1. Configuration of the ParaStation system
Within this section the basic configuration procedure to enable ParaStation will be described. It covers the
configuration of ParaStation5 using TCP/IP (Ethernet) and the optimized ParaStation5 protocol p4sock.
configuration of ParaStation5 using TCP/IP (Ethernet) and the optimized ParaStation5 protocol p4sock.
The primarily configuration work is reduced to editing the central configuration file
parastation.conf
,
which is located in
/etc
.
A template file can be found in
/opt/parastation/config/parastation.conf.tmpl
. Copy this file
to
/etc/parastation.conf
and edit it as appropriate.
This section describes all parameters of
/etc/parastation.conf
necessary to customize ParaStation
for a basic cluster environment. A detailed description of all possible configuration parameters in the
configuration file can be found within the parastation.conf(5) manual page.
configuration file can be found within the parastation.conf(5) manual page.
The following steps have to be executed on the frontend node to configure the ParaStation daemon psid(8):
1. Copy template
Copy
the
file
/opt/parastation/config/parastation.conf.tmpl
to
/etc/
parastation.conf
.
The template file contains all possible parameters known by the ParaStation daemon psid(8). Most
of these parameters are set to their default value within lines marked as comments. Only those that
have to be modified in order to adapt ParaStation to the local environment are enabled. Additionally all
parameters are exemplified using comments. A more detailed description of all the parameters can be
found in the parastation.conf(5) manual page.
of these parameters are set to their default value within lines marked as comments. Only those that
have to be modified in order to adapt ParaStation to the local environment are enabled. Additionally all
parameters are exemplified using comments. A more detailed description of all the parameters can be
found in the parastation.conf(5) manual page.
The template file is a good starting point to create a working configuration of ParaStation for your
cluster. Beside basic information about the cluster, this template file defines all hardware components
ParaStation is able to handle. Since these definitions require a deeper knowledge of ParaStation, it is
easier to copy the template file anyway.
cluster. Beside basic information about the cluster, this template file defines all hardware components
ParaStation is able to handle. Since these definitions require a deeper knowledge of ParaStation, it is
easier to copy the template file anyway.
2. Define Number of nodes
The parameter NrOfNodes has to be set to the actual number of nodes within the cluster. Front end
nodes have to be considered as part of the cluster. E.g. if the cluster contains 8 nodes with a fast
interconnect plus a front end node then NrOfNodes has to be set to 9 in order to allow the start of parallel
tasks from this machine.
nodes have to be considered as part of the cluster. E.g. if the cluster contains 8 nodes with a fast
interconnect plus a front end node then NrOfNodes has to be set to 9 in order to allow the start of parallel
tasks from this machine.
3. HWType
In order to tell ParaStation which general kind of communication hardware should be used, the HWType
parameter has to be set. This could be changed on a per node basis within the nodes section (see below).
parameter has to be set. This could be changed on a per node basis within the nodes section (see below).
For clusters running ParaStation5 utilizing the optimized ParaStation communication stack on Ethernet
hardware of any flavor this parameter has to be set to:
hardware of any flavor this parameter has to be set to:
HWType { p4sock ethernet }
This will use the optimized ParaStation protocol, if available. Otherwise, TCP/IP will be used.