KitchenAid SIDE BY SIDE REFRIGERATOR ユーザーズマニュアル
9
3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
two more turns. Do not overtighten.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See “Prepare the Water System.”
NOTE: It may take up to 24 hours for your ice maker to begin
producing ice.
producing ice.
Prepare the Water System
Please read before using the water system.
Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
sure that the water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. For Style 1,
lift up the wire shutoff arm as shown. For Style 2, move the
switch to the OFF (right) setting as shown. The ON/OFF
switch is located on the top right side of the freezer
compartment.
switch to the OFF (right) setting as shown. The ON/OFF
switch is located on the top right side of the freezer
compartment.
Style 1
Style 2
NOTES:
■
If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the
horizontal position.
base grille filter is properly installed and the cap is in the
horizontal position.
■
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system.
of unknown quality without adequate disinfection before
or after the system.
2. Use a sturdy container to depress the water dispenser bar
until the water begins to flow. Flush the water system by
dispensing and discarding 1.5 gal. (5.4 L) of water. Cleaning
the system will take approximately 3 minutes and will help
clear air from the line. Additional flushing may be required in
some households.
dispensing and discarding 1.5 gal. (5.4 L) of water. Cleaning
the system will take approximately 3 minutes and will help
clear air from the line. Additional flushing may be required in
some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
of the dispenser.
3. Open the freezer door and turn on the ice maker. For Style 1,
lower the wire shutoff arm. For Style 2, move the switch to
the ON (left) position. Please refer to the “Ice Maker and
Storage Bin” section for further instructions on the operation
of your ice maker.
the ON (left) position. Please refer to the “Ice Maker and
Storage Bin” section for further instructions on the operation
of your ice maker.
■
Allow 24 hours to produce the first batch of ice.
■
Discard the first three batches of ice produced.
■
Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
maximum ice feature to increase the production of ice.
Factory Trim Kit
(on some models)
There may be an occasion when you will need to remove the
factory-installed trim kit, such as moving the refrigerator to a new
home or installing custom-made decorator panels. Please read
all instructions before removing the trim kit and decorator panels.
factory-installed trim kit, such as moving the refrigerator to a new
home or installing custom-made decorator panels. Please read
all instructions before removing the trim kit and decorator panels.
A. Bulb
B. Nut (provided)
B. Nut (provided)
A
B
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
fire, or electrical shock.
WARNING
Freezer Door
Refrigerator Door
A. Decorator panels
B. Filler panels
B. Filler panels
C. Handles
A
B
A
B
A
B
C