Campbell Hausfeld MW2500 Series 사용자 설명서

Operating Instructions and Parts List

2.  If repair or replacement of cord or 

plug is necessary, do not connect 
grounding wire to either flat blade 
terminal. The wire with insulation 
having an external surface that 
is green (with or without yellow 
stripes) is the grounding wire.

3.  Check with a qualified electrician 

or serviceman if grounding 
instructions are not completely 
understood, or if in doubt as 
to whether product is properly 
grounded. Do not modify plug 
provided; if it will not fit outlet, 
have proper outlet installed by a 
qualified electrician.

LUbrIcatIOn
This is an oilless product and DOeS 
nOt require lubrication to operate.

beFOre FIrSt Start-UP
break-In PrOceDUre
(Complete this procedure before 
using compressor for the first time. 
Once completed, it is not necessary to 
repeat.)
1.  Turn regulator knob fully clockwise 

(to the right) to open air flow.

2.  Do not attach a hose or any other 

fitting to the compressor.

3.  Turn On / OFF switch to OFF 

position.

4.  Plug in power cord.
5.  Turn On / OFF switch to On 

position and run compressor for 30 
minutes.

6.  Turn On / OFF switch to OFF 

position.

7.  Unplug power cord.

The compressor is now ready for use.

beFOre each Start-UP
OPeratInG PrOceDUre
1.  Turn regulator knob fully 

counterclockwise (to the left) to 
close air flow. 

2.  Connect air hose to outlet of 

regulator.

3.  Turn On / OFF switch to OFF 

position.

4.  Plug in power cord.
5.  Turn On / OFF switch to On 

position and let compressor run 
until it reaches automatic shutoff 
pressure.

6.  Attach tire chuck or tool to end of 

hose.

7.  Turn regulator knob clockwise (to 

the right) to desired pressure of 
tool being used.

On / OFF cycLInG OF cOMPreSSOr
In the On / aUtO position, the 
compressor pumps air into the tank. 
When a shut-off (preset “cut-out”) 
pressure is reached, the compressor 
automatically shuts off.

If the compressor is left in the  
On / aUtO position and air is depleted 
from the tank by use of a tire chuck, 
tool, etc., the compressor will restart 
automatically at its preset “cut-in” 
pressure. When a tool is being used 
continuously, the compressor will cycle 
on and off automatically. 

In the OFF position, the pressure 
switch cannot function and the 
compressor will not operate. Make 
sure switch is in OFF position when 
connecting or disconnecting power 
cord from electrical outlet.

PreSSUre GaUGeS
The large gauge next to the regulator 
knob indicates air pressure going to 
hose (and any tool attached to end of 
hose).

The small gauge next to the safety 
valve indicates air pressure in tank.

Moisture in compressed air will form into droplets as it comes from an 
air compressor pump. When humidity is high or when a compressor is in 
continuous use for an extended period of time, this moisture will collect 
in the tank. When using a paint spray or sandblast gun, this water will be 
carried from the tank through the hose, and out of the gun as droplets mixed 
with the spray material.
IMPOrtant: This condensation will cause water spots in a paint job, 
especially when spraying other than water based paints. If sandblasting, it 
will cause the sand to cake and clog the gun, rendering it ineffective.
A filter in the air line, located as near to the gun as possible, will help 
eliminate this moisture.

TEST

RESET

Grounded 

Outlet

Grounding 

Pin