Nokia 8850 Manual Suplementar
AT Command Set for Nokia 8850
26
Copyright © 2000. Nokia Mobile Phones. All rights reserved.
+CMOD Call Mode
This command sets the call mode for further dialling command ATD or for next
answering command ATA . To prevent the possibility that alternating mode calls are
originated or answered accidentally, <mode> is automatically reset to value 0 after
each call. Note that alternating call answering operations from an external UI may
change +CMOD values. (GSM 07.07 sections 6.4, 6.6, and annexes E, F).
answering command ATA . To prevent the possibility that alternating mode calls are
originated or answered accidentally, <mode> is automatically reset to value 0 after
each call. Note that alternating call answering operations from an external UI may
change +CMOD values. (GSM 07.07 sections 6.4, 6.6, and annexes E, F).
Syntax:
AT+CMOD=<mode>
Set call mode. The default option is 0.
AT+CMOD?
Query current setting.
Response is +CMOD:<mode>.
Response is +CMOD:<mode>.
AT+CMOD=?
Show supported modes.
Response is +CMOD: (list of supported
<mode>'s).
Response is +CMOD: (list of supported
<mode>'s).
Values for <mode>:
0
single mode (default)
1
alternating voice/fax (teleservice 61)
2
alternating voice/data (bearer service 61)
3
voice followed by data (bearer service 81)
+CMSS Send Message from Storage
This command sends a message with the location value <index> from a preferred
message storage selected with AT+CPMS command (see page 32). If a new
recipient address <da> is given, it shall be used instead of the one stored with the
message. Reference value <mr> is returned to DTE on successful message delivery.
(GSM 07.05 section 3.5.2.)
message storage selected with AT+CPMS command (see page 32). If a new
recipient address <da> is given, it shall be used instead of the one stored with the
message. Reference value <mr> is returned to DTE on successful message delivery.
(GSM 07.05 section 3.5.2.)
Syntax:
AT+CMSS=<index>, <da>,<toda>
Responses:
text mode (+CMGF=1) and sending ok:
+CMSS: <mr>[,<scts>]
PDU mode (+CMGF=0) and sending ok:
+CMSS: <mr>[,<ackpdu>]
text mode (+CMGF=1) and sending ok:
+CMSS: <mr>[,<scts>]
PDU mode (+CMGF=0) and sending ok:
+CMSS: <mr>[,<ackpdu>]
Default option: [,"",129/145]
AT+CMSS=?
AT+CMSS=?
Shows whether command has been
implemented.
implemented.
Parameters:
<index>
location number
<mr>
message reference number
<da>
destination address
<toda>
type of destination address, 129 for
normal and 145 for international access
('+' character automatically added to
address)
normal and 145 for international access
('+' character automatically added to
address)
+CNMA New Message Acknowledgement to ME/TA
This command confirms correct reception of a new message (SMS-DELIVER or
SMS-STATUS-REPORT) which is routed directly to the TE. This acknowledgement
command (causing ME to send RP-ACK to the network) shall be used when +CSMS
(see page 38) parameter <service> equals 1. TA shall not send another +CMT or
+CDS result code to TE before previous one is acknowledged. If ME does not get
acknowledgement within required time (network timeout), ME should send RP-
ERROR to the network. ME/TA shall automatically disable routing to TE by setting
both <mt> and <ds> values of +CNMI to zero. (GSM 07.05 section 3.4.4. PDU
entering as specified in GSM 07.05. Command is available only when +CSMS=1 is
supported.)
SMS-STATUS-REPORT) which is routed directly to the TE. This acknowledgement
command (causing ME to send RP-ACK to the network) shall be used when +CSMS
(see page 38) parameter <service> equals 1. TA shall not send another +CMT or
+CDS result code to TE before previous one is acknowledged. If ME does not get
acknowledgement within required time (network timeout), ME should send RP-
ERROR to the network. ME/TA shall automatically disable routing to TE by setting
both <mt> and <ds> values of +CNMI to zero. (GSM 07.05 section 3.4.4. PDU
entering as specified in GSM 07.05. Command is available only when +CSMS=1 is
supported.)
For some products only <n>=0 is applicable with some phone models.