Fujitsu MAN3367 Manual Do Utilizador
C141-E124-01EN
5 - 9
Table 5.2
Sense and subsense codes (4 of 5)
C*
Q*
Name
Explanation
Sense
key
37
00
Rounded parameter
Rounding processing of the MODE SELECT parameter
specified by the command was performed.
specified by the command was performed.
1
3D
00
Invalid bits in IDENTIFY
message
message
"1" was specified in the reserve bit of the IDENTIFY message.
5
03
Logical unit failed Self-
Test
Test
The test segment error occurred during the Self-Test
4
3E
04
Logical unit unable to update The IDD failed to update the Self-Test result log
4
01
Microcode has been changed Microcode was changed by another INIT.
6
02
Changed operating definition Operating definition was changed.
6
3F
05
Device identifier changed
Device identifier was changed.
6
40
nn
Diagnostic failure on
component "nn"
component "nn"
An error was detected in self-diagnosis. ("nn" is a Fujitsu unique
code)
code)
• 81: Buffer RAM compare error/bus error
• 82: Program RAM compare error/bus error
• 83: HDC register check error
• 84: Firmware header/check sum error
• 85: Firmware type unmatch
• 86: Parameter header/check sum error
• 88: Drive Serial No. unmatch
• 89: DE type unmatch
• 8F: Other MPU peripheral circuit diagnostic error
• 92: Spindle motor firmware initialize error
• 83: HDC register check error
• 84: Firmware header/check sum error
• 85: Firmware type unmatch
• 86: Parameter header/check sum error
• 88: Drive Serial No. unmatch
• 89: DE type unmatch
• 8F: Other MPU peripheral circuit diagnostic error
• 92: Spindle motor firmware initialize error
4
43
00
Message error
A message sent by the IDD was illegally rejected.
B
nn
Internal target failure
An internal hardware error was detected in the IDD. ("nn" is a
Fujitsu unique code)
Fujitsu unique code)
• 83: Undefined interrupt occurred.
• 92: Unexpected FMT interrupt occurred.
• 99: Overflow error occurred at SPC FIFO.
• 9A: Unexpected SPC interrupt occurred.
• 9B: SPC detected illegal command interrupt.
• 9C: SPC detected illegal write interrupt.
• 9D: SPC detected Sync offset error interrupt.
• A3: DBM buffer CRC error.
• A8: Data late error.
• B0: Flash ROM erasing failed.
• B1: Flash ROM writting failed.
• B2: No writing program to flash ROM
• C0: RDCLK error (FMT hang up)
• D1: DSP downloading failed.
• D2: DSP overrun (watch dog timer timeout, DRV harderror)
• D3: Serve gate window error
• D4: Illegal error was reported from DSP.
• D5: Write gate check error (unmatch)
• 92: Unexpected FMT interrupt occurred.
• 99: Overflow error occurred at SPC FIFO.
• 9A: Unexpected SPC interrupt occurred.
• 9B: SPC detected illegal command interrupt.
• 9C: SPC detected illegal write interrupt.
• 9D: SPC detected Sync offset error interrupt.
• A3: DBM buffer CRC error.
• A8: Data late error.
• B0: Flash ROM erasing failed.
• B1: Flash ROM writting failed.
• B2: No writing program to flash ROM
• C0: RDCLK error (FMT hang up)
• D1: DSP downloading failed.
• D2: DSP overrun (watch dog timer timeout, DRV harderror)
• D3: Serve gate window error
• D4: Illegal error was reported from DSP.
• D5: Write gate check error (unmatch)
4
90
Next Sector ID Compare
Error
Error
HDC detected unexpected sector ID.
4
91
WCS RAM Parity Error
Parity error detected in Formatter’s WCS RAM
4
44
E0
Calibration Error
Any error detected during calibration
4
* C: Sense Code, Q: Sub-sense Code