RoboteQ AX2550 Manual Do Utilizador
AX1500 Motor Controller User’s Manual
107
Reception Watchdog
ond indicates the minimum joystick position and 2.0 milliseconds indicates the maximum
joystick position. When the joystick is in the center position, the pulse should be 1.5ms.
joystick position. When the joystick is in the center position, the pulse should be 1.5ms.
Note that the real pulse-length to joystick-position numbers that are generated by your R/C
radio may be different than the ideal 1.0ms to 2.0ms discussed above. To make sure that
the controller captures the full joystick movement, the AX1500 defaults to the timing val-
ues shown in Figure 70. These vales can be changed and stored as new defaults.
radio may be different than the ideal 1.0ms to 2.0ms discussed above. To make sure that
the controller captures the full joystick movement, the AX1500 defaults to the timing val-
ues shown in Figure 70. These vales can be changed and stored as new defaults.
The AX1500 has a very accurate pulse capture input and is capable of detecting changes in
joystick position (and therefore pulse width) as small as 0.4%. This resolution is superior to
the one usually found in most low cost R/C transmitters. The AX1500 will therefore be able
to take advantage of the better precision and better control available from a higher quality
R/C radio, although it will work fine with lesser expensive radios as well.
joystick position (and therefore pulse width) as small as 0.4%. This resolution is superior to
the one usually found in most low cost R/C transmitters. The AX1500 will therefore be able
to take advantage of the better precision and better control available from a higher quality
R/C radio, although it will work fine with lesser expensive radios as well.
Internally, the measured pulse width is compared to the reference minimum, center and
maximum pulse width values. From this is generated a number ranging from -127 (when
the joystick is in the min. position), to 0 (when the joystick is in the center position) to +127
(when the joystick is in the max position). This number is then used to set the motors’
desired speed or position that the controller will then attempt to reach.
maximum pulse width values. From this is generated a number ranging from -127 (when
the joystick is in the min. position), to 0 (when the joystick is in the center position) to +127
(when the joystick is in the max position). This number is then used to set the motors’
desired speed or position that the controller will then attempt to reach.
For best results, reliability and safety, the controller will also perform a series of correc-
tions, adjustments and checks to the R/C commands, as described in the following sec-
tions.
tions, adjustments and checks to the R/C commands, as described in the following sec-
tions.
Reception Watchdog
Immediately after it is powered on, if in the R/C mode, the controller is ready to receive
pulses from the R/C radio and move the motors accordingly.
pulses from the R/C radio and move the motors accordingly.
If no pulses are present, the motors are disabled.After powering on the R/C radio receiver
and transmitter, and if the wiring is correct, the controller will start receiving pulses. For a
preset amount of time, the controller will monitor the pulse train to make sure that they are
regular and therefore genuine R/C radio command pulses. After that, the motors are
enabled.
and transmitter, and if the wiring is correct, the controller will start receiving pulses. For a
preset amount of time, the controller will monitor the pulse train to make sure that they are
regular and therefore genuine R/C radio command pulses. After that, the motors are
enabled.
This power-on Watchdog feature prevents the controller from becoming active from para-
site pulses and from moving the motors erratically as a result.
site pulses and from moving the motors erratically as a result.
1.05ms
min
center
max
joystick position:
R/C pulse timing:
0.45ms
0.9ms
FIGURE 70. Joystick position vs. pulse duration default values