Справочник Пользователя для Sony PDW-F335KL
![Sony](https://files.manualsbrain.com/attachments/7e61ba04cadfce70cb41a1a70ef1d62a30f0a5fe/common/fit/150/50/682a2570dc00831b079177f57c62a2915dd3423eb752334060fbcf750d89/brand_logo.png)
42
Preparing the Audio Input System
Chap
te
r 2
Pr
epa
epa
ra
tio
n
n
s
3
Open the CAC-12 and remove the microphone
adaptor.
adaptor.
When attaching an ECM-673/674/678, use the
microphone adaptor supplied with the ECM-673/674/
678.
microphone adaptor supplied with the ECM-673/674/
678.
4
Place an external microphone (electret condenser
microphone such as the ECM-673/674/678) in the
CAC-12.
microphone such as the ECM-673/674/678) in the
CAC-12.
5
Connect the microphone cable to the AUDIO IN CH-
1 or CH-2 connector.
1 or CH-2 connector.
6
Set the switches as follows.
• Set the AUDIO IN input selection switch as
indicated below, depending on the type of
microphone used.
- When using a microphone with an internal
microphone used.
- When using a microphone with an internal
power supply, set it to MIC (center).
- When using a microphone with an external
power supply, set it to MIC +48V ON (right).
• Set the AUDIO IN (CH-1/CH-2/CH-3/CH-4) switch
for the channel to which the microphone is
connected to REAR (for CH-1/CH-2) or R (for CH-
3/CH-4).
connected to REAR (for CH-1/CH-2) or R (for CH-
3/CH-4).
7
Switch the input level to match the sensitivity of the
microphone used.
microphone used.
Switch the input level by changing the REAR MIC
REF setting on the AUDIO-1 page of the
MAINTENANCE menu (factory default setting is –60
dB).
REF setting on the AUDIO-1 page of the
MAINTENANCE menu (factory default setting is –60
dB).
For more details, see page 117.
• If the input level on this unit is not at an appropriate
setting for the microphone sensitivity, loud sounds may
be distorted, and the signal-to-noise ratio may be
affected.
be distorted, and the signal-to-noise ratio may be
affected.
• In order for the AUDIO IN CH-1 and CH-2 connectors
on the camcorder to be able to provide a phantom 48 V
power supply, female XLR connectors (3-pin) are fitted.
If the microphone cable has a female connector, use an
adaptor.
power supply, female XLR connectors (3-pin) are fitted.
If the microphone cable has a female connector, use an
adaptor.
• When you detach a CAC-12 Microphone Holder once
you have attached to the camcorder, be careful not to
lose the two screws fixing the CAC-12 (in step 1). After
detaching the CAC-12, be sure to put the two screws
back into their original places.
lose the two screws fixing the CAC-12 (in step 1). After
detaching the CAC-12, be sure to put the two screws
back into their original places.
Attaching a UHF Synthesized Tuner
You can record sound by using a wireless microphone
system consisting of the following.
• WRT-804/807S UHF Wireless Microphone
• WRT-822/824 UHF Synthesized Transmitter
• WRR-855/861/862 UHF Synthesized Tuner
system consisting of the following.
• WRT-804/807S UHF Wireless Microphone
• WRT-822/824 UHF Synthesized Transmitter
• WRR-855/861/862 UHF Synthesized Tuner
For the power source of this wireless microphone system,
use Sony lithium-ion battery packs.
use Sony lithium-ion battery packs.
For details on using the wireless microphone system, see
the operating instructions for the microphone and tuner.
the operating instructions for the microphone and tuner.
Microphone adaptor
Open the CAC-12.
Loosen the screw.
ECM-673/674/678 or
similar microphone
similar microphone
Close the CAC-12.
Tighten the screw.
m
Notes
Note
to AUDIO IN CH-1/CH-2
connector
connector
Monaural microphone
AUDIO IN (CH-1/CH-2)
switches
switches