Справочник Пользователя для Sony PDW-F335KL
44
Connecting the Remote Control Unit
Chap
te
r 2
Pr
epa
epa
ra
tio
n
n
s
• Set the AUDIO IN input selection switch to MIC for
the channel to which the audio output cable is
connected.
connected.
• Set the AUDIO IN (CH-1/CH-2/CH-3/CH-4) switch
for the channel to which the audio output cable is
connected to REAR (for CH-1/CH-2) or R (for CH-
3/CH-4).
connected to REAR (for CH-1/CH-2) or R (for CH-
3/CH-4).
Connecting Line Input Audio
Equipment
Equipment
1
Connect an audio mixer or other external audio system
component to the AUDIO IN CH-1/CH-2 connector as
shown below.
component to the AUDIO IN CH-1/CH-2 connector as
shown below.
2
Set the AUDIO IN input selection switch to LINE for
the channel to which the external audio equipment is
connected.
the channel to which the external audio equipment is
connected.
Selection of the recording audio input
Set the AUDIO IN (CH-1/CH-2/CH-3/CH-4) switch for
the channel to which the audio device is connected to
REAR (for CH-1/CH-2) or R (for CH-3/CH-4).
Set the AUDIO IN (CH-1/CH-2/CH-3/CH-4) switch for
the channel to which the audio device is connected to
REAR (for CH-1/CH-2) or R (for CH-3/CH-4).
Connecting the Remote
Control Unit
Control Unit
Connecting the RM-B150/B750 Remote Control Unit
enables remote control of the principal camera and VDR
functions.
Connecting the remote control unit to the REMOTE
connector (8-pin) automatically puts the camcorder into
remote control mode. If you disconnect the remote control
unit, the remote control mode is cancelled.
enables remote control of the principal camera and VDR
functions.
Connecting the remote control unit to the REMOTE
connector (8-pin) automatically puts the camcorder into
remote control mode. If you disconnect the remote control
unit, the remote control mode is cancelled.
Refer to the RM-B150/B750 Operation Manual for the
maximum cable length for connections between the
camcorder and the RM-B150/B750.
maximum cable length for connections between the
camcorder and the RM-B150/B750.
Before connecting/disconnecting the remote control unit
to/from the camcorder, be sure to turn off the camcorder
POWER switch.
to/from the camcorder, be sure to turn off the camcorder
POWER switch.
Camcorder switch functions when the
remote control unit is connected
remote control unit is connected
Connecting the remote control unit disables the following
switches on the camcorder.
• GAIN switch
• OUTPUT/DCC switch
• WHITE BAL switch
• AUTO W/B BAL switch
• SHUTTER switch
switches on the camcorder.
• GAIN switch
• OUTPUT/DCC switch
• WHITE BAL switch
• AUTO W/B BAL switch
• SHUTTER switch
Paint adjustment when the remote control
unit is connected
unit is connected
The settings of the paint adjustment that were in effect the
last time the remote control unit was used are recalled.
last time the remote control unit was used are recalled.
When the monitor is connected to the
remote control unit
remote control unit
The MONITOR connector (BNC type) of the RM-B150/
B750 outputs the same signal as that from the VIDEO
OUT connector on the camcorder.
B750 outputs the same signal as that from the VIDEO
OUT connector on the camcorder.
LINE
MIC
+48V ON
FRONT
WIRELESS
REAR
AUDIO IN
to audio mixer, etc.
AUDIO IN (CH-1/CH-2) switch:
Set to REAR.
Set to REAR.
AUDIO IN CH-1/CH-2
connector
connector
AUDIO IN input selection switch:
Set to LINE.
Set to LINE.
Note
RM-B150/B750
REMOTE
connector
connector
Remote control cable