Инструкция для Whirlpool MEDB850YG

15

If you experience

Possible Causes

Solution

Dryer Results (cont.)

Clothes are not drying 

satisfactorily or drying 

times are too long

The load is too large and heavy  

to dry quickly.

Separate the load to tumble freely.

Fabric softener sheets are blocking 

the grille.

The air outlet grille is just inside the door, behind the lint screen. Check 

that it is not blocked by a fabric softener sheet. 

Use only one fabric softener sheet, and use it only once.

The dryer is located in a room with 

temperature below 45ºF (7ºC).

Proper operation of dryer cycles requires temperatures above 45ºF (7ºC).

The dryer is located in a closet.

Closet doors must have ventilation openings at the top and bottom of the 

door. The front of the dryer requires a minimum of 1” (25 mm) of airspace, 

and, for most installations, the rear of the dryer requires 5” (127 mm). See 

Installation Instructions.

Cycle time is too short

The load may not be contacting the 

sensor strips on Sensor Cycles.

Level the dryer. See Installation Instructions. All four dryer feet should be 

in firm contact with the floor.

Clothes are coming out of the 

Steam cycles with damp or wet 

spots.

Under certain environmental or installation conditions you may 

experience underdrying. Select the Custom Refresh cycle. Then select 

the appropriate number of garments for the load from the Number of 

Garments option.

The sensor cycle is ending early.

Change the dryness level setting on Sensor Cycles. Increasing or 

decreasing the dryness level will change the amount of drying time in a 

cycle. If loads are consistently ending too early, see also “Changing the 

Sensor Cycle settings to increase drying time”.

Lint on load

Lint screen is clogged with lint.

Clean lint screen before each load.

Stains on load

Improper use of fabric softener.

Add dryer fabric softener sheets at the beginning of the cycle. Fabric 

softener sheets added to a partially dried load can stain your garments. 

Do not use fabric softener sheets with steam cycles.

Stains on drum

Loose dyes in clothes.

Drum stains are caused by dyes in clothing (usually blue jeans).  

These will not transfer to other clothing.

Loads are wrinkled

The load was not removed from 

dryer at the end of the cycle.

Select Auto or Custom Refresh cycle (on some models) to tumble 

the load with water and heat. These cycles are best for smoothing out 

wrinkles and reducing odors from loads consisting of wrinkle-free cotton, 

cotton polyester blends, common knits, and synthetic garments.

NOTE: Refer to garment care label instructions. Dry clean only garments 

are not recommended.

The dryer was overloaded.

Dry smaller loads that can tumble freely. When using the Custom 

Refresh cycle (on some models), be sure to select the correct number 

of garments to be refreshed. Results may also vary depending on fabric 

type. This cycle is best for reducing wrinkles and odors from loads 

consisting of wrinkle-free cotton, cotton polyester blends, common knits, 

and synthetics.

For steam cycles, the water is not 

properly connected with the dryer.

Make sure water is connected to the dryer. Check that water inlet hose is 

connected to both the faucet and dryer’s water inlet valve. Check that the 

water supply is turned on.

Odors

Recent painting, staining, or 

varnishing in the area where your 

dryer is located.

Ventilate the area. When the odors or fumes are gone from the area, 

rewash and dry the clothing.

For steam cycles, the water is not 

properly connected with the dryer.

Make sure water is connected to the dryer. Check that water inlet hose is 

connected to both the faucet and dryer’s water inlet valve. Check that the 

water supply is turned on.

Odors are left in garments after 

wearing.

To remove odors left in garments after wearing, select Auto Refresh. 

This cycle is best for reducing wrinkles and odors from loads consisting 

of wrinkle-free cotton, cotton polyester blends, common knits, and 

synthetics.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –  

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.