Monessen Hearth 7000 Series 用户手册
O
O
P
P
E
E
R
R
A
A
T
T
I
I
N
N
G
G
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
25
Pilot
LIGHTING INSTRUCTIONS
MILLIVOLT CONTROL
8.
With the control knob pushed in, push in and
release the piezo ignitor button to light the pilot.
release the piezo ignitor button to light the pilot.
9.
Continue pushing the control knob in for a further
60 seconds to prevent the flame detector from
shutting off the gas while the probe is warming up.
Release the control knob.
60 seconds to prevent the flame detector from
shutting off the gas while the probe is warming up.
Release the control knob.
10.
•If the pilot will not stay lit after several tries, turn
the gas control knob clockwise to “OFF” and
call your service technician or gas supplier.
•If the knob does not pop out when released, stop
and call your service technician or gas supplier.
the gas control knob clockwise to “OFF” and
call your service technician or gas supplier.
•If the knob does not pop out when released, stop
and call your service technician or gas supplier.
11. Turn knob counterclockwise to “ON”
12. After the pilot has been lit for one minute, the
12. After the pilot has been lit for one minute, the
burner can be turned on. Turn RS-OFF-ON switch
to “ON” or turn RS-OFF-ON switch to “RS” and
remote switch to “ON”.
to “ON” or turn RS-OFF-ON switch to “RS” and
remote switch to “ON”.
Gas
Valve
1.
STOP! Read the safety information below
on this label.
on this label.
2.
Open access door on left side of floor to
reveal gas valve, then locate RS-OFF-ON
rocker switch on left side inner chamber.
reveal gas valve, then locate RS-OFF-ON
rocker switch on left side inner chamber.
3.
Turn RS-OFF-ON rocker switch to “OFF”.
Turn remote switch to “OFF”
Turn remote switch to “OFF”
4.
Push in gas valve knob and turn clockwise
to “OFF”
to “OFF”
5.
Wait five (5) minutes to clear out any gas.
Than smell for gas, including near the floor.
If you smell gas, STOP! Follow “B” in the
safety information below on this label. If
you don’t smell gas, go to the next step.
Than smell for gas, including near the floor.
If you smell gas, STOP! Follow “B” in the
safety information below on this label. If
you don’t smell gas, go to the next step.
6.
Find Pilot-located under the log.
7.
Turn gas valve counterclockwise
to “Pilot”
to “Pilot”
1.
Open left side access door.
2.
Turn RS-OFF-ON rocker switch to “OFF”.
3.
Push in gas valve knob slightly and turn clockwise to “OFF”.
4.
Close access door.
TO TURN OFF GAS TO APPLIANCE
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:
If you do not follow these Instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition
device (piezo) which automatically lights the
pilot. When lighting the pilot, follow these
instructions exactly.
pilot. When lighting the pilot, follow these
instructions exactly.
B. BEFORE OPERATING smell all around the
appliance area for gas. Be sure to smell next to
the floor because some gas is heavier than air
and will settle on the floor.
the floor because some gas is heavier than air
and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
*
Do not try to light any appliance
*
Do not touch any electric switch; do not use
any phone in your building.
any phone in your building.
*
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier’s
instructions.
neighbor's phone. Follow the gas supplier’s
instructions.
*
If you cannot reach your gas supplier, call the
fire department.
fire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn by
hand, don’t try to repair it, call a
qualified service technician. Force or
attempted repair may result in a fire or
explosion
If the knob will not push in or turn by
hand, don’t try to repair it, call a
qualified service technician. Force or
attempted repair may result in a fire or
explosion
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been
under water.