3M 2210 产品宣传页
Receiver Operation:
Battery Installation or Replacement:
33 KHz
2210
Receiver
Front Panel
577 Hz
Gain
Adjust
1.
Press
Press
to turn receiver
on and see battery level.
Hold down
for continuous
Battery T
est
. If bar
. If bar
graph is to the left of the battery level mark, replace
batteries.
Note:
when batteries are low
, the battery
test indicator
remains on.
2.
Press
Press
to match
Fr
equency
equency
to transmitter output
or select
for passive power locating.
3.
Press
Press
to set
Gain
when
bar
graph
is
not
not
visible
o
r i
s c
lo
se
d. For
High V
olume
(
),
hold down
while turning unit on. T
o
return to normal volume,
turn unit of
f, then on again.
4.
Make broad sweeps with receiver handle in line
Make broad sweeps with receiver handle in line
with tar
get cable path to get maximum bar graph
closure; press
. Maximum bar graph and numeric
indication occurs directly over cable.
5.
Place the receiver upright on the surface directly
Place the receiver upright on the surface directly
over cable. W
ith handle parallel to path, press
to display estimated
Depth
. Press again to display
numeric
Curr
ent
indication. Cable with highest
indication. Cable with highest
current indication is the tar
get
. Press
. Press
to return to
trace mode, and press
. Unit returns to trace mode
automatically after eight seconds.
Note:
T
o
use the 2210 with the Active Duct Pr
obe
(sonde) or the EMS Marker Locating Accessory
, r
efer
to their Operating Instructions.
6 ‘C’ cells
6 ‘AA
’
cells
Do
not
not
connect
batteries
improperly
, charge or dispose of in fire.
Batteries may leak or explode and cause personal injury
.
Always
remove batteries when storing the units. Since regulations vary
,
consult applicable regulations or authorities before disposal.
CAUTION!
T
echnical
Information:
Active F
requencies:
577 Hz and 33 KHz
Passive F
requency
:
60
H
z Power
Battery
Life:
Receiver
84
hours,
hours,
typical
(Normal
audio
level)
T
ransmitter
50 hours, typical (Normal mode)
10 hours, typical (Boost mode)
Recommended
Batter
ies:
Dur
a
Dur
a
cell
MN1500
AA
Alkaline
Alkaline
Duracell
MN1400
C
Alkaline
Temper
atur
e Range:
Oper
ating
-4
°
F
to
122
122
°
F (
-2
-2
0
°
to
50
°
C)
Stor
age
-40
°
F
to
158
158
°
F (
-4
-4
0
°
to
70
°
C)
Receiver
W
eight:
eight:
3 lbs.
9
9
oz.
(1.8
(1.8
kg)
T
ransmitter
W
eight:
5 lbs. 2 oz. (
2
.4
kg)
Shipping
W
eight
15 lbs. 7 oz. (7.1 kg)
Duracell
is a registered trademark of Duracell , Inc.
Optional
Accessories:
3” Dyna-Coupler Kit:
3019
1” Dyna-Coupler:
3005
6” Dyna-Coupler:
1196
Active Duct Probe (sonde)
3229
Ground Extension Cable
9043
EMS Marker Locating Accessory
Single Freq.
2205
All Freq.
2206
3M
T
T
elecom Systems Division
6801 River Place Blvd.
Austin, TX 78726-9000
1996
3M
78–8097–5171-8 Rev
.
A
Dynatel
2210 Cable Locator
Operating Instructions
September
1996
78-8097-5171-8 Revision A
Set Up
(Use one of three methods)
Prepare the transmitter using one of the three
following methods:
Direct Connect
Induction
Dyna-Coupler
Go to
T
ransmitter
Operation
to turn the unit on and
apply tone to the cable.
Refer to
Receiver Operation
to prepare the receiver
and locate the cable.
For passive power locating, go directly to
Receiver
Operation
.
Note:
For mor
e detailed locating instructions and
advanced locating techniques, ask your 3M sales
repr
esentative for a fr
esentative for a fr
ee publication called Cable and
Pipe Locating T
echniques.
Dynatel is a r
egister
ed trademark of 3M