Hearth & Home Technologies GO24MTCH 用户手册
Hearth & Home Technologies • Grand Oak Match Light Gas Log Sets • 4004-300 Rev C • 12/05
3
A. Design and Installation Considerations
The Gas Log Hearth Kit consists of the following:
• Log
Set
• Burner/Pan
Assembly
• Grate
Assembly
• Rock
Wool
• Sand
• Lava
• Lava
Rock
• Damper
Stop
• Vermiculite
• Platinum
• Platinum
Embers
B. Tools and Supplies Needed
Tools and supplies normally required for installation:
Pliers
Phillips screwdriver
Tape measure
Crescent wrenches
Gas shutoff valve
Non-corrosive leak check solution
3/4 in. wrench, 7/16 in. wrench
Phillips screwdriver
Tape measure
Crescent wrenches
Gas shutoff valve
Non-corrosive leak check solution
3/4 in. wrench, 7/16 in. wrench
Improper installation, adjustment, alteration, service
or maintenance can cause injury or property damage.
Refer to the owner’s information manual provided with
this appliance. For assistance or additional information
consult a qualifi ed installer, service agency or the gas
supplier.
or maintenance can cause injury or property damage.
Refer to the owner’s information manual provided with
this appliance. For assistance or additional information
consult a qualifi ed installer, service agency or the gas
supplier.
WARNING
Sharp Edges
• Wear protective gloves
• Wear protective gloves
and safety glasses during
installation.
installation.
CAUTION
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
WARNING
• Keep
children
away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high
temperatures.
• Keep clothing, furniture, draperies and other
combustibles away.
Glass and other surfaces are hot during
operation and cool down.
operation and cool down.
C. Important!
• Do not remove any of the attached metal plates, which
contain important safety and operating information.
• Keep the appliance area clear and free of all combustible
materials, gasoline and other fl ammable vapors and
liquids.
liquids.
•
Any safety screen or guard removed during servicing must
be replaced before operation.
be replaced before operation.
• A qualifi ed service technician must perform installation
and repair. The appliance should be inspected and cleaned
annually by a qualifi ed service technician. More frequent
cleaning may be required due to excessive lint, dust, pet
hair, etc. It is imperative that the control compartments,
burners and air passageways are unobstructed during
operation.
annually by a qualifi ed service technician. More frequent
cleaning may be required due to excessive lint, dust, pet
hair, etc. It is imperative that the control compartments,
burners and air passageways are unobstructed during
operation.
-
Review proper placement of logs, rockwool, lava rock
and vermiculite.
and vermiculite.
- Check
the
wiring.
- Ensure there are no gas leaks.
- Ensure
- Ensure
the
fl ow of combustion and ventilation air is not
obstructed (front grilles and vent caps).
• Before installing into a solid fuel burning fi replace, the
chimney and fi rebox should be inspected and cleaned to
remove soot, creosote, ashes, paint, bird nests etc.
remove soot, creosote, ashes, paint, bird nests etc.
• Annual examination of the chimney must be performed
by a qualifi ed agency to ensure proper ventilation of fl ue
gases created by this appliance.
gases created by this appliance.
Fire Risk
Exhaust Fumes Risk
•
Exhaust Fumes Risk
•
Do NOT use this appliance as a “vent-free
heater.
heater.
The fl ue must be permanently open according
to Tables 1 and 2.
to Tables 1 and 2.
WARNING
• Have the chimney and adjacent structure inspected
and cleaned by qualifi ed professionals. Hearth & Home
Technologies recommends that NFI or CSIA certifi ed
professionals, or technicians under the direction of certifi ed
professionals, conduct a minimum of an NFPA 211 Level 2
inspection of the chimney.
Technologies recommends that NFI or CSIA certifi ed
professionals, or technicians under the direction of certifi ed
professionals, conduct a minimum of an NFPA 211 Level 2
inspection of the chimney.
•
Replace component parts of the chimney and fi replace as
specifi ed by the professionals.
specifi ed by the professionals.
•
Ensure all joints are properly engaged and the chimmney
is properly secured.
is properly secured.
• Do not allow fans to blow directly into the fi replace. Avoid
any drafts that alter burner fl ame pattern.
•
Do not use a blower insert, heat exchanger insert or other
accessories not approved for use with this appliance.
accessories not approved for use with this appliance.