lift-master 500lm 用户手册
Lift-Master
®
The Professional Line
UNIVERSAL RADIO CONTROL
Model 500LM
Model 500-1LM
Model 500-2LM
Receiver Only
(With 1 Transmitter)
(With 2 Transmitters)
F.C.C . rules prohibit adjustments to or modification of receiver and/or transmitter circuitry expect for changing the code setting and replacing the transmitter
battery. THERE ARE NO USER SERVICEABLE PARTS.
battery. THERE ARE NO USER SERVICEABLE PARTS.
MANUFACTURED UNDER 1 OR MORE OF THE FOLLOWING U.S. PATENTS: RE29,525; 4,037,201; 4,750,118; 4,806,930
MODEL 85 TRANSFORMER MAY BE REQUIRED IF YOUR GARAGE DOOR OPENER IS
A BRAND OTHER THAN LIFT-MASTER, CHAMBERLAIN OR SEARS.
A BRAND OTHER THAN LIFT-MASTER, CHAMBERLAIN OR SEARS.
INSTALL THE RECEIVER OUT OF THE REACH OF CHILDREN. DO NOT ALLOW CHILDREN TO OPERATE
RECEIVER OR TRANSMITTER(S). SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR MAY
RESULT FROM MISUSE OF THE OPENER.
RECEIVER OR TRANSMITTER(S). SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR MAY
RESULT FROM MISUSE OF THE OPENER.
The receiver may be installed in one of two ways: 1. attached to an inside wall of the garage with connecting bell wire (not supplied).
2. mounted directly on the door opener with clips provided.
When installing two or more receivers in garage, position them at least 10 feet apart to prevent electronic interference.
NOTE: Models 500-1LM and 500-2LM are factory pre-set with matching receiver and transmitter codes.
CAUTION: Do not attempt to open the receiver back panel. THERE ARE NO USER SERVICEABLE PARTS.
2. mounted directly on the door opener with clips provided.
When installing two or more receivers in garage, position them at least 10 feet apart to prevent electronic interference.
NOTE: Models 500-1LM and 500-2LM are factory pre-set with matching receiver and transmitter codes.
CAUTION: Do not attempt to open the receiver back panel. THERE ARE NO USER SERVICEABLE PARTS.
MOUNTING RECEIVER ON OPENER
Fully extend antenna wire below bottom of case shown.
Loosen the three terminal screws on either side of the receiver
(labeled 1,2, and 3). Insert one end of a mounting clip under
each terminal. Make sure clips are positioned to clear the
receiver flange, as shown. DO NOT RETIGHTEN AT THIS
TIME.
Loosen the three terminal screws on either side of the receiver
(labeled 1,2, and 3). Insert one end of a mounting clip under
each terminal. Make sure clips are positioned to clear the
receiver flange, as shown. DO NOT RETIGHTEN AT THIS
TIME.
Loosen three terminal screws on the opener used for push
button control and radio power.
button control and radio power.
Leaving the push button bell wire in place, insert other ends of
the mounting slips under the opener terminal screws.
the mounting slips under the opener terminal screws.
NOTE: If the number sequence of opener terminals doesn’t
match the receiver, turn the receiver around (so back is facing
out) and complete the connection.
match the receiver, turn the receiver around (so back is facing
out) and complete the connection.
Retighten the terminal screws on opener and receiver.
Reconnect power to the opener. The receiver push bar should
light. If it does not, use Transformer Model 85.
NOTE: With the transformer, use a 2-wire connection ONLY.
Attach mounting clips to receiver terminals 1 and 2, and to the
opener terminals used for push button controls. Plug the
transformer into the receiver as shown, and into a 120 Volt
outlet.
Reconnect power to the opener. The receiver push bar should
light. If it does not, use Transformer Model 85.
NOTE: With the transformer, use a 2-wire connection ONLY.
Attach mounting clips to receiver terminals 1 and 2, and to the
opener terminals used for push button controls. Plug the
transformer into the receiver as shown, and into a 120 Volt
outlet.
Fully extend the antenna wire below bottom of case.
Fasten the receiver to an inside garage wall with wood screws
provided. A convenient place is alongside the service door and
OUT OF THE REACH OF CHILDREN.
provided. A convenient place is alongside the service door and
OUT OF THE REACH OF CHILDREN.
Attach one end of 3-strand bell wire (not supplied) to receiver
terminals 1, 2 and 3. Connect the other end to the three opener
terminals used for push button controls and radio power. Use
insulated staples to secure bell wire between receiver and opener.
terminals 1, 2 and 3. Connect the other end to the three opener
terminals used for push button controls and radio power. Use
insulated staples to secure bell wire between receiver and opener.
Reconnect power to the opener. The receiver push bar should
light. If it does not, use Transformer Model 85.
light. If it does not, use Transformer Model 85.
NOTE: With the transformer, use a 2-wire connection ONLY.
Attach wire to receiver terminals 1 and 2 and to the opener
terminals used for push button control. Plug the transformer
into receiver and 120 Volt outlet as shown.
Attach wire to receiver terminals 1 and 2 and to the opener
terminals used for push button control. Plug the transformer
into receiver and 120 Volt outlet as shown.
Side 2 contains installation and service information as well as code setting instruction for models with transmitter (s).