Redline Communications Inc. AN100UA 用户手册
Red
MAX
™
Base Station
User Manual
Doc. #70-00058-01-01
Proprietary Redline Communications © 2007
July 13, 2007
Page 66 of 119
Refresh: Click
Refresh Time
to poll the time server for the current time.
DHCP Relay Agent Parameters
The subscriber can obtain an IP address from the DHCP server only through an base
station acting as a DHCP Relay Agent. A subscriber can not obtain an IP address from
any DHCP server on the network segment connected to its local Ethernet port. The base
station (acting as a DHCP Relay Agent) can be configured for two different modes:
SS-s should use the same DHCP Server as SC: Select this option to have the base
station forward all subscriber DHCP requests to the DHCP server that the base station
used to obtain its IP address (valid only if field Obtain IP Parameters from DHCP Server
is enabled above).
SS-s should use the following DHCP Server: Select this option to specify the DHCP
server to be used by subscribers.
station acting as a DHCP Relay Agent. A subscriber can not obtain an IP address from
any DHCP server on the network segment connected to its local Ethernet port. The base
station (acting as a DHCP Relay Agent) can be configured for two different modes:
SS-s should use the same DHCP Server as SC: Select this option to have the base
station forward all subscriber DHCP requests to the DHCP server that the base station
used to obtain its IP address (valid only if field Obtain IP Parameters from DHCP Server
is enabled above).
SS-s should use the following DHCP Server: Select this option to specify the DHCP
server to be used by subscribers.
DHCP Server: Specify the IP address of a DHCP server. The base station forwards
all subscriber DHCP requests to this address.
all subscriber DHCP requests to this address.
It important to configure the correct lease options on your DHCP Server:
a) The base station requires option 4, the address of a ToD Server (RFC-868).
b) If you do not wish your devices to display GMT, you must add option 2 (Time Offset).
This is a value denoting the number of seconds to offset your time from GMT. For
example, for the offset of +2 hours you should enter 7200 (some DHCP servers may
require entering hexadecimal value). In North America, EST is -5 hours (-18000 seconds)
from GMT and the negative value must be entered.
Important: The base station must be rebooted to activate changes to the DHCP Relay
Agent settings.
a) The base station requires option 4, the address of a ToD Server (RFC-868).
b) If you do not wish your devices to display GMT, you must add option 2 (Time Offset).
This is a value denoting the number of seconds to offset your time from GMT. For
example, for the offset of +2 hours you should enter 7200 (some DHCP servers may
require entering hexadecimal value). In North America, EST is -5 hours (-18000 seconds)
from GMT and the negative value must be entered.
Important: The base station must be rebooted to activate changes to the DHCP Relay
Agent settings.
VLAN Management
Enable Management with VLAN Tagged Traffic: Check this box to enable
management using VLAN tagged traffic for the SM CID. This setting is used to
configure tagged management for operation in systems where a single VLAN is used to
control the base station wireless equipment and the user equipment. After enabling this
setting, only traffic with the specified VID is recognized for any management commands.
This setting does not effect operation of the RS-232 Console port.
VLAN ID: Enter the VLAN ID. Only traffic tagged with this VLAN ID is recognized by
the sector controller management process.
Important: The VLAN network support should be verified before enabling this feature.
If the base station is not reachable using the VLAN tagged traffic, the Console port
(RS-232) CLI command must be used to disable this setting.
Save: Click
management using VLAN tagged traffic for the SM CID. This setting is used to
configure tagged management for operation in systems where a single VLAN is used to
control the base station wireless equipment and the user equipment. After enabling this
setting, only traffic with the specified VID is recognized for any management commands.
This setting does not effect operation of the RS-232 Console port.
VLAN ID: Enter the VLAN ID. Only traffic tagged with this VLAN ID is recognized by
the sector controller management process.
Important: The VLAN network support should be verified before enabling this feature.
If the base station is not reachable using the VLAN tagged traffic, the Console port
(RS-232) CLI command must be used to disable this setting.
Save: Click
Save
to save and apply the current settings.
Cancel: Click
Cancel
to discard all changes and return to the main screen.
Default: Click
Default
to set all settings to the factory default settings.