Bosch Appliances Home Security System ICP-CC404 用户手册
ICP-CC404 | Installation Guide | 6.0
System Functions
28 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
To set the first Test Report:
1. Enter the Installer Code and press [1][AWAY].
1. Enter the Installer Code and press [1][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
indicators flash.
2. Enter the number of days (1 to 15) until the first
Test Report is sent and press [AWAY].
Two beeps sound and the STAY and AWAY
indicators turn off. The system returns to the
disarmed state.
Two beeps sound and the STAY and AWAY
indicators turn off. The system returns to the
disarmed state.
Each time you enter Installer’s
Programming Mode, the first Test Report
time defaults to the repeat interval set in
Location 366.
Programming Mode, the first Test Report
time defaults to the repeat interval set in
Location 366.
The number of days counts down by one
at 2400 hours as set in Locations 901 to
904 (refer to Section 17.15 System
Time on page 72).
at 2400 hours as set in Locations 901 to
904 (refer to Section 17.15 System
Time on page 72).
Example
If the repeat interval is set to 7 days, but you want the
first Test Report to be sent in 2 days, enter:
first Test Report to be sent in 2 days, enter:
[1 2 3 4 1][AWAY][2][AWAY]
6.1.2
Changing Domestic Phone Numbers
When the system is set up for domestic dialing, this
function allows the installer to view and program the
telephone numbers that the system calls if an alarm
occurs. Refer to Section 9.0 Domestic Dialing on
page 40 for more information.
function allows the installer to view and program the
telephone numbers that the system calls if an alarm
occurs. Refer to Section 9.0 Domestic Dialing on
page 40 for more information.
To change domestic phone numbers:
1. Enter the Installer Code and press [2][AWAY].
1. Enter the Installer Code and press [2][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
If there are telephone numbers programmed,
they appear one digit at a time using the remote
codepad indicators. Refer to Table 21 on page 28
for the indicators and their meanings.
If there are no telephone numbers programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after you
enter the last digit of the last phone number.
indicators flash.
If there are telephone numbers programmed,
they appear one digit at a time using the remote
codepad indicators. Refer to Table 21 on page 28
for the indicators and their meanings.
If there are no telephone numbers programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after you
enter the last digit of the last phone number.
2. Enter the first phone number.
Each digit appears as you enter it.
3. If you are programming another phone number,
press [STAY][4] to separate the end of one phone
number and the beginning of the next.
If you are not programming other numbers, go to
Step 5.
number and the beginning of the next.
If you are not programming other numbers, go to
Step 5.
4. Repeat Steps 2 and 3 to program another phone
number.
5. Press [AWAY] to exit from this mode.
Table 20:
Domestic Dialing Digits
Digit
Required
Required
Number to
Program
Program
Digit
Required
Required
Number to
Program
Program
0
0
8
8
1 1 9 9
2
2
10
refer to 0
3 3 * *
1
4
4
#
* 2
5
5
4 sec pause
* 3
6
6
break
* 4
7 7 15
*
5
Example
If you want to program two separate telephone
numbers (9672 1777 and 9672 1233), enter:
numbers (9672 1777 and 9672 1233), enter:
[1 2 3 4 2][AWAY][9 6 7 2 1 7 7 7][STAY]
[4 9 6 7 2 1 2 3 3][AWAY]
[4 9 6 7 2 1 2 3 3][AWAY]
You can suspend domestic dialing at any time (for
example, you are moving house and do not want the
system to continue calling your work place or mobile
phone).
example, you are moving house and do not want the
system to continue calling your work place or mobile
phone).
To disable domestic dialing:
Enter the Installer Code and press [2][AWAY]
[STAY][4][AWAY].
[STAY][4][AWAY].
Table 21:
Codepad Indicators When Changing
Phone Numbers
Phone Numbers
Zone Indicators
MAINS
Digit 1 2 3 4 5 6 7 8 Indicator
0
X
1
X
2
X
3
X
4
X
5
X
6
X
7
X
8
X
9
X
X
11
X
X
12
X
X
Pause
X
X
Break
X
X
15
X
X
6.1.3 Change
Telco
Arming or Disarming
Sequence
Program the call forward sequence to automatically
operate when you arm the system in AWAY Mode.
This feature is only available if the call forward option
is available from your telecommunication provider.
operate when you arm the system in AWAY Mode.
This feature is only available if the call forward option
is available from your telecommunication provider.