Bosch Appliances Home Security System ICP-CC404 用户手册
ICP-CC404 | Installation Guide | 6.0
System Functions
30 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
To disable the Telco disarming sequence:
Enter the Installer Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
[AWAY][STAY][4][AWAY].
To program the Telco arming sequence – easy
call forward (immediate on):
1. Enter the Installer Code and press [3][AWAY].
call forward (immediate on):
1. Enter the Installer Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
indicators flash.
2. Press [1][AWAY] button to change the Telco
arming sequence. Three beeps sound.
If a call forwarding sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 23 on page 29 for the indicators and their
meanings.
If there is no call forward sequence programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the call forward sequence is shown.
If a call forwarding sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 23 on page 29 for the indicators and their
meanings.
If there is no call forward sequence programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the call forward sequence is shown.
3. Press [STAY][1 2 1] and enter the phone number
to which you want calls from the control panel
diverted.
diverted.
4. Press [STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
disarmed state.
Example
If you want to automatically divert all incoming calls
to another telephone number (for example, 9672
1777) when the system is armed in AWAY Mode,
enter:
to another telephone number (for example, 9672
1777) when the system is armed in AWAY Mode,
enter:
[1 2 3 4 3][AWAY][1][AWAY][STAY]
[1 2 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the Telco arming sequence at any
time.
time.
To disable the Telco arming sequence:
Enter the Installer Code and press [3][AWAY][1]
[AWAY][STAY][4][AWAY].
[AWAY][STAY][4][AWAY].
To program the Telco disarming sequence – easy
call forward (immediate off):
1. Enter the Installer Code and press [3][AWAY].
call forward (immediate off):
1. Enter the Installer Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
indicators flash.
2. Press [2][AWAY] to change the Telco disarming
sequence.
Three beeps sound.
If a Telco disarming sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 23 for the indicators and their meanings.
Three beeps sound.
If a Telco disarming sequence is already
programmed, the sequence appears one digit at a
time using the remote codepad indicators. Refer
to Table 23 for the indicators and their meanings.
If there is no Telco disarming sequence
programmed, an additional two beeps sound after
entering this mode. These two beeps normally
sound after the last digit of the sequence appears.
programmed, an additional two beeps sound after
entering this mode. These two beeps normally
sound after the last digit of the sequence appears.
3. Press [STAY][2 2 1][STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
disarmed state.
You can suspend the Telco disarming sequence at
any time.
any time.
To disable the Telco disarming sequence:
Enter the Installer Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
[AWAY][STAY][4][AWAY].
6.1.4
Setting STAY Mode 2 Zones
This function allows the installer to select the zones
that are automatically isolated when the system is
armed in STAY Mode 2.
that are automatically isolated when the system is
armed in STAY Mode 2.
To arm the system in STAY Mode 2, press and hold
[0] until two beeps sound.
[0] until two beeps sound.
Refer to Section 6.3.3 on page 37 or Section 4.5 Arming
the System in STAY Mode 2 on page 17 for more
information.
the System in STAY Mode 2 on page 17 for more
information.
To set STAY Mode 2 zones:
1. Enter the Installer Code and press [4][AWAY].
1. Enter the Installer Code and press [4][AWAY].
Three beeps sound and the STAY indicator
flashes.
flashes.
2. Enter the number of the zone you want to
automatically isolate and press [STAY].
The corresponding zone indicator flashes.
The corresponding zone indicator flashes.
3. Repeat Step 2 for each zone you want to select.
As you select each zone to isolate, the
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the zones you selected and the
STAY indicator turn off.
disarmed state.
The indicators for the zones you selected and the
STAY indicator turn off.
Example
If you want to select zones 2, 5, and 6, enter:
[1 2 3 4 4][AWAY][2][STAY][5][STAY][6][STAY]
[AWAY]
[AWAY]
You can disable all zones selected to automatically
isolate for STAY Mode 2 at any time.
isolate for STAY Mode 2 at any time.
To disable STAY Mode 2 zones:
Enter the Installer Code and press [4][AWAY]
[AWAY].
[AWAY].
6.1.5
Satellite Siren Service Mode
If the SS914 Satellite Siren (EDMSAT) is connected
to Output 1, this function allows you to perform
service work on the system without activating the
satellite siren. The satellite siren returns to its normal
working state the next time the system is armed.
to Output 1, this function allows you to perform
service work on the system without activating the
satellite siren. The satellite siren returns to its normal
working state the next time the system is armed.