Bosch Appliances Home Security System ICP-CC404 用户手册
ICP-CC404 | Installation Guide | 6.0 System Functions
Bosch Security Systems, Inc. | 12/08 | F01U089401-02
31
To enter Satellite Siren Service Mode:
Enter the Installer Code and press [5][AWAY].
Three beeps sound.
6.1.6
Turning Telephone Monitor Mode On and
Off
Off
Telephone Monitor Mode allows you to use the
remote codepad for visual representation of data
transmissions between the control panel and the base
station receiver. The dialing sequence is also shown in
this mode.
remote codepad for visual representation of data
transmissions between the control panel and the base
station receiver. The dialing sequence is also shown in
this mode.
The codepad beeps once every 2 sec when
Telephone Monitor Mode is active, whether the
system is in Installer’s Programming Mode or normal
operating mode. The first five indicators show the
progressive steps during a transmission to the base
station receiver.
Telephone Monitor Mode is active, whether the
system is in Installer’s Programming Mode or normal
operating mode. The first five indicators show the
progressive steps during a transmission to the base
station receiver.
Table 24:
Telephone Monitor Mode Indications
Zone LED
Dialing Event
1
Telephone line seized
2
Dialing phone number
3
Handshake received
4 Data
being
transmitted
5
Kiss-off received
None
Telephone line released
To turn Telephone Monitor Mode on:
Enter the Installer Code and press [6][AWAY].
Three beeps sound.
To turn Telephone Monitor Mode off:
Enter the Installer Code and press [6][AWAY].
Two beeps sound.
You must exit from Telephone Monitor
Mode to resume normal operations.
Mode to resume normal operations.
6.1.7
Walk Test Mode
Walk Test Mode allows you to test detection devices
to ensure they are functioning correctly. Before
activating Walk Test Mode, isolate any zones that are
not required for testing. Refer to Section 4.11 Isolating
Zones on page 21 for more information.
to ensure they are functioning correctly. Before
activating Walk Test Mode, isolate any zones that are
not required for testing. Refer to Section 4.11 Isolating
Zones on page 21 for more information.
To enter Walk Test Mode:
1. Enter the Installer Code and press [7][AWAY].
1. Enter the Installer Code and press [7][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash. The codepad beeps once per sec
when Walk Test Mode is active.
indicators flash. The codepad beeps once per sec
when Walk Test Mode is active.
2. Unseal and seal the zones to be tested.
The codepad sounds one long beep and the horn
speaker sounds one short beep each time a zone
is sealed or unsealed.
speaker sounds one short beep each time a zone
is sealed or unsealed.
3. Press [AWAY] to exit from this function.
Two beeps sound and the STAY and AWAY
indicators turn off. The system returns to the
disarmed state.
indicators turn off. The system returns to the
disarmed state.
6.1.8
Event Memory Recall Mode
This function allows you to play back the last 40
system events that occurred. Event Memory Recall
Mode reports all alarms and each arming or
disarming of the system and helps with
troubleshooting system faults. The events are shown
using the codepad indicators.
system events that occurred. Event Memory Recall
Mode reports all alarms and each arming or
disarming of the system and helps with
troubleshooting system faults. The events are shown
using the codepad indicators.
To enter Event Memory Recall Mode:
Enter the Installer Code and press [8][AWAY].
Three beeps sound. The events are played back by
the codepad indicators in reverse chronological order.
Three beeps sound. The events are played back by
the codepad indicators in reverse chronological order.
Example
If the events occurred in the following order:
1. System armed in AWAY Mode
2. Alarm in Zone 3
3. Alarm in Zone 4
4. System disarmed
The alarm memory plays back in this order:
1. All indicators off except MAINS (System
1. System armed in AWAY Mode
2. Alarm in Zone 3
3. Alarm in Zone 4
4. System disarmed
The alarm memory plays back in this order:
1. All indicators off except MAINS (System
disarmed)
2. Zone 4 and AWAY indicators light (Alarm in
Zone 4)
3. Zone 3 and AWAY indicators light (Alarm in
Zone 3)
4. AWAY indicator lights (System armed in AWAY
Mode)
Each event is indicated by a beep and a lit indicator.
Resetting a disarmed 24-Hour Alarm is indicated by a
beep only.
Resetting a disarmed 24-Hour Alarm is indicated by a
beep only.
After the last event, three beeps sound to indicate the
end of playback. You can stop the replay at any time
by pressing [AWAY].
end of playback. You can stop the replay at any time
by pressing [AWAY].
If the system is armed in STAY Mode 1 or
STAY Mode 2, the STAY indicator shows
the event memory playback. There is no
differentiation between STAY Mode 1 and
STAY Mode 2.
STAY Mode 2, the STAY indicator shows
the event memory playback. There is no
differentiation between STAY Mode 1 and
STAY Mode 2.
If power is removed from the control
panel, the memory of all events is saved.
panel, the memory of all events is saved.
6.2 Master
Code
Functions
Master Code Functions allow users with the
appropriate priority level to perform certain
supervisory level functions. You can use these
functions only when the system is disarmed.
appropriate priority level to perform certain
supervisory level functions. You can use these
functions only when the system is disarmed.