Bosch Appliances Home Security System ICP-CC404 用户手册
ICP-CC404 | Installation Guide | 6.0 System Functions
Bosch Security Systems, Inc. | 12/08 | F01U089401-02
37
To enter Event Memory Recall Mode:
Enter your Master Code and press [8][AWAY].
Three beeps sound. The events are played back by
the codepad indicators in reverse chronological order.
Three beeps sound. The events are played back by
the codepad indicators in reverse chronological order.
Example
If the events occurred in the following order:
1. System armed in AWAY Mode
2. Alarm in Zone 3
3. Alarm in Zone 4
4. System disarmed
The alarm memory plays back in this order:
1. All indicators off except MAINS (System
1. System armed in AWAY Mode
2. Alarm in Zone 3
3. Alarm in Zone 4
4. System disarmed
The alarm memory plays back in this order:
1. All indicators off except MAINS (System
disarmed)
2. Zone 4 and AWAY indicators light (Alarm in
Zone 4)
3. Zone 3 and AWAY indicators light (Alarm in
Zone 3)
4. AWAY indicator lights (System armed in AWAY
Mode)
Each event is indicated by a beep and a lit indicator.
Resetting a disarmed 24-Hour Alarm is indicated by a
beep only.
Resetting a disarmed 24-Hour Alarm is indicated by a
beep only.
After the last event, three beeps sound to indicate the
end of playback. You can stop the replay at any time
by pressing [AWAY].
end of playback. You can stop the replay at any time
by pressing [AWAY].
If the system is armed in STAY Mode 1 or
STAY Mode 2, the STAY indicator shows
the event memory playback. There is no
differentiation between STAY Mode 1 and
STAY Mode 2.
STAY Mode 2, the STAY indicator shows
the event memory playback. There is no
differentiation between STAY Mode 1 and
STAY Mode 2.
If the control panel is powered down, the
memory of all events is lost.
memory of all events is lost.
6.3 Hold-Down
Functions
Hold-down functions allow easy activation of specific
operations. When you press and hold a button for
2 sec, two beeps sound and the corresponding
function operates. The hold-down functions are listed
below.
operations. When you press and hold a button for
2 sec, two beeps sound and the corresponding
function operates. The hold-down functions are listed
below.
6.3.1
Arming the System in AWAY Mode
Pressing and holding [#] until two beeps sound arms
the system in AWAY Mode. This function operates
only if you select Option 2 in Location 429 (refer to
Section 18.6 Consumer Options 2 on page 75).
the system in AWAY Mode. This function operates
only if you select Option 2 in Location 429 (refer to
Section 18.6 Consumer Options 2 on page 75).
6.3.2
Arming the System in STAY Mode 1
Pressing and holding [*] until two beeps sound arms
the system in STAY Mode 1. This function operates
only if you select Option 2 in Location 429 (refer to
Section 18.6 Consumer Options 2 on page 75).
the system in STAY Mode 1. This function operates
only if you select Option 2 in Location 429 (refer to
Section 18.6 Consumer Options 2 on page 75).
If there was no alarm during the armed cycle,
pressing and holding [*] a second time disarms the
system from STAY Mode 1. To enable single button
disarming from STAY Mode 1 using this function,
select Option 4 in Location 429.
pressing and holding [*] a second time disarms the
system from STAY Mode 1. To enable single button
disarming from STAY Mode 1 using this function,
select Option 4 in Location 429.
If an alarm occurred or entry warning was activated,
a valid User Code is required to disarm the system.
a valid User Code is required to disarm the system.
Refer to Section 14.3.6 Zone Options 2 on page 58 for
information on programming each zone to
automatically isolate in STAY Mode 1.
information on programming each zone to
automatically isolate in STAY Mode 1.
6.3.3
Arming the System in STAY Mode 2
Pressing and holding [0] until two beeps sound arms
the system in STAY Mode 2. This function operates
only if you select Option 2 in Location 429 (refer to
Section 18.6 Consumer Options 2 on page 75).
the system in STAY Mode 2. This function operates
only if you select Option 2 in Location 429 (refer to
Section 18.6 Consumer Options 2 on page 75).
If there was no alarm during the armed cycle,
pressing and holding [0] a second time disarms the
system from STAY Mode 2. To enable single button
disarming from STAY Mode 2 using this function,
select Option 4 in Location 429.
pressing and holding [0] a second time disarms the
system from STAY Mode 2. To enable single button
disarming from STAY Mode 2 using this function,
select Option 4 in Location 429.
If an alarm occurred or entry warning was activated,
a valid User Code is required to disarm the system.
a valid User Code is required to disarm the system.
For more information, refer to Section 6.1.4 Setting
STAY Mode 2 Zones on page 30 (using the Installer
Code function) or Section 6.2.5 Setting STAY Mode 2
Zones on page 35 (using the Master Code function).
STAY Mode 2 Zones on page 30 (using the Installer
Code function) or Section 6.2.5 Setting STAY Mode 2
Zones on page 35 (using the Master Code function).
6.3.4 Horn
Speaker
Test
Pressing and holding [1] until two beeps sound
activates the horn speaker for a two-sec burst. No
other sounding device operates during this mode.
activates the horn speaker for a two-sec burst. No
other sounding device operates during this mode.
6.3.5 Bell
Test
Pressing and holding [2] until two beeps sound
activates the internal screamers for a two-sec burst.
No other sounding device operates during this mode.
activates the internal screamers for a two-sec burst.
No other sounding device operates during this mode.
If the SS914 Satellite Siren (EDMSAT) is connected
to the control panel, this function tests both the horn
speaker and the strobe connected to the satellite siren
for a 2-sec burst.
to the control panel, this function tests both the horn
speaker and the strobe connected to the satellite siren
for a 2-sec burst.
6.3.6 Strobe
Test
Pressing and holding [3] operates the strobe. No other
device operates during this mode.
device operates during this mode.
If the SS914 Satellite Siren (EDMSAT) is connected
to the control panel, this function also tests the strobe
on the satellite siren.
to the control panel, this function also tests the strobe
on the satellite siren.
To turn the strobe test on:
Press and hold [3] until three beeps sound.
The strobe flashes.
To turn the strobe test off:
Press and hold [3] until two beeps sound.
The strobe stops flashing.