Manualsbrain.com
  1. Handbücher
  2. Marken
  3. Panasonic
  4. AJ-D850P
  5. Benutzerhandbuch

Panasonic AJ-D850P Benutzerhandbuch

Download
Seite von 102
– 91 –
SERVO CONTROL
ERROR
Counter display
Description
VTR operation
(Restart condition)
REEL DIR UNMATCH
If the reel motor at the take-up side is running in the 
reverse direction, the AUTO OFF lamp lights, and the 
message display flashes.
STOP
(POWER OFF
→
ON)
REEL TENSION ERROR
SERVO COMM ERROR
SERVO ERROR
S-FF/REW TIMEOVER
S REEL ROTA TOO
FAST
T REEL ROTA TOO
FAST
T REEL TORQUE
ERROR
UNLOAD ERROR
S REEL TORQUE
ERROR
WINDUP ERROR
If an abnormal tension at the supply side is detected 
in the reel mode, the AUTO OFF lamp lights, and the 
message display flashes.
STOP
(POWER OFF
→
ON)
When the servo microcomputer does not follow the 
instructions of the system control microcomputer 
even when 10 seconds have elapsed, the AUTO OFF 
lamp lights, and the message display flashes.
STOP
(POWER OFF
→
ON)
When there is no response from the servo micro-
computer for 1 or more seconds, the AUTO OFF 
lamp lights, and the message display flashes.
STOP
(POWER OFF
→
ON)
When only the servo microcomputer was reset in an 
instantaneous power failure, the AUTO OFF lamp 
lights, and the message display flashes.
STOP
(POWER OFF
→
ON)
If the start/end processing operation is not completed, 
the AUTO OFF lamp lights, and the message display 
flashes.
STOP
(POWER OFF
→
ON)
If the supply reel motor should rotate at an ab-
normally fast rate, the AUTO OFF lamp lights, and 
the message display flashes.
STOP
(POWER OFF
→
ON)
If an abnormal torque applied to the supply reel motor 
is detected, the AUTO OFF lamp lights, and the 
message display flashes.
STOP
(POWER OFF
→
ON)
If the take-up reel motor should rotate at an ab-
normally fast rate, the AUTO OFF lamp lights, and 
the message display flashes.
STOP
(POWER OFF
→
ON)
If an abnormal torque applied to the take-up reel 
motor is detected, the AUTO OFF lamp lights, and 
the message display flashes.
STOP
(POWER OFF
→
ON)
If the tape has not been wound up during unloading, 
the AUTO OFF lamp lights, and the message display 
flashes.
STOP
(POWER OFF
→
ON)
If the tape was not wound up at less than the 
standard speed (1
×
) when the total tape amount was 
not detected or if abnormal tape slack or tension was 
detected at speeds above 1
×
 after the total tape 
amount was detected, the AUTO OFF lamp lights, 
and the message display flashes.
STOP
(POWER OFF
→
ON)
WINDUP REEL NOT
ROTA
If, after the cassette has been inserted, the tape take-
up reel has not wound up the tape at the standard 
speed (1
×
) or faster while the total tape amount is not 
detected and while the tape is traveling in the forward 
or reverse direction, the AUTO OFF lamp lights, and 
the message display flashes.
STOP
(POWER OFF
→
ON)
Monitor display
SERVO CONTROL
ERR
REEL DIR UNMATCH
REEL TENSION ERROR
SERVO COMM ERROR
SERVO ERROR
S-FF/REW TIMEOVER
S REEL TOO FAST
T REEL TOO FAST
T REEL TORQUE
ERR
UNLOAD ERROR
S REEL TORQUE
ERR
WINDUP ERROR
W-UP REEL NOT ROTA